Question about 1995 Ford Taurus

1 Answer

Car was recently flipped. I belive there is oil in the Clyinder.. how do i go about getting the oil out? and what else do i need to do to get my car running again?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 880 Answers

First remove all of the spark plugs. Look at the electrodes to see if they are oil fouled. If so clean them to remove the oil and any carbon, reinstall, spray a small amount of "starting fluid" into the air intake and try to start the engine. If there is oil in the cylinders you may have to repeat this. If the plugs are old and worn or they seem to continue to foul you may need to purchase new plugs.

Posted on Feb 08, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What should I do? Get another car?

Possible bad spark plug or coil pack. Weak compression could be bent valve, worn piston rings, or head gasket. Black at the tail pipe is from unburned fuel from your cylinder miss.

Aug 19, 2014 | 2000 Toyota Corolla

1 Answer

I cannot bleed the clutch on my kia caranvil

First lets make sure we are on the same page here.Your saying you have no clutch resivioir and the system is feed from the brake master cylinder correct .Now the clutch has two clylinders the master witch atteches to the clutch pedal with the rod and it mounted on the fire wall . The slave cylinder is mounted between the bell houseing and the engine . And to replace this you would need to remove the transmission and actualy moves the pressure plate springs back when the pedal is depressed . Think of it like a light its eighter on or off and pushing the pedal down turns it off Normaly the clutch would be bleed at the slave cylinder there should be a bleeder fitting near the top of the bell hoseing. And should be bleed just a brake line no trick you just have to find the bleeder . Check for fluid at the clutch master on the pedal if you see any oil at all leaking you will never be able to keep it bleed sometimes there bad even when new .If oil can get out air is GETTING IN and it will constantly need to be rebleed. Any questions fell free to ask

Mar 19, 2012 | Cars & Trucks

1 Answer

Just recently got a 2000 Cadillac Seville SLS with 58,000 miles. It was my late aunts. It pretty much sat in her driveway for a couple of years. Very limited use. I started to drive it and it ran great....

Findout the code. You Said It's Realated To The Transmission I Just Pick Mine Up For What I Belive Is The Samething The Tcc & The Code Is P1860 Thats The Tourque Converter Circuit! You Should Getit Changed Because It'll Save You Gas Pluse Less Tress On The Transmission & Engine & Could Cause Gear **** Stall !

Oct 15, 2010 | 2000 Cadillac Seville

1 Answer

Just bought 07' accord with 31, 000 miles and oil was changed by dealer before delivery with next change due in 3000 miles, now oil gauge in dash is saying oil at 15%,

Guess the guys at the dealership forgot to reset your oil chage light. Check your oil to make sure its not black. If its at a good brownish color then get to your oil life screen on your car and i belive you hold down the check mark button till the oil light resets (30sec) or so.

Mar 01, 2010 | 2007 Honda Accord Sedan

1 Answer

My oil light is on I cant find anything wrong I need to reset the oil light

if oil light is on, you need to change your oil. or at least the car things you need to change it according to the last time the oil light was reset. check manual on how to reset light. on 99 caravans, i belive it has to do with the radio or the clock/calander display on the roof.

Jan 13, 2010 | 1999 Dodge Grand Caravan

1 Answer

My sis-n-law's L200 stalled on the interstate a couple of nights ago. She couldn't give it gas or anything and coasted to the shoulder of the road. She said there were no sounds, just a dead car. After...

possibly a broken or very loose timing chain,,,it usually doesnt make any sound,the tensioner for the timing chain probably lost oil supply ,oil pressure to it and slacked up the chain causing it to jump or break from the low oil or just bad luck on a bad part,but if it did jump time or break the chain itmore than likely bent the valves in the cylinder head,,youll need a new or used head as the valve guide could be damaged and its cheaper to replace the head,,the bottom end of the engine is ok,,,,but check compression,and it should be 170 plus and all about even no more than 15 psi difference across the cylinders,if it is a low compression reading youll have to remove the clyinder and check the valves,,common on the 4 clyinder L200

Oct 18, 2009 | 2002 Saturn L-Series

1 Answer

Sunroof won't open/close

Try this!!! There is a Tilt button and a seperate open/close button I belive . try holding the Tilt button up while holding the open/close button up also at the same time.WHILE THE CAR IS ON!!. Then turn your car off while still holding the buttons up. Then turn your car on again and should work un its totally fried from the rain. What this does is it re-programs your sunroof to work again. Hope this works

let me know at

Jun 30, 2009 | 1997 Honda CR-V

1 Answer

Oil light flashing, last oil change 7 wks ago

I belive they didn't reset the oil light timer. I belive the sequence is 1. key on (not acc with engine off)
2. step on the brake pedal 5 times within 10 seconds. 3. key off. 4. start car. 5. check if the light went out. you may have to try it a few times to get it.

Jun 25, 2009 | 2003 Pontiac Grand Am

1 Answer

OBD-II trouble codes P0001 and P0410. Can't get a straight answer on what to do.

what kind of car do you have and what year and is it a 4 6 or 8 clyinder engine need to know to help you sir.

Jun 13, 2009 | 1998 Volvo S70

1 Answer

Ford bronco ii 88 eddie bawer

That Oil Pump Should be Located Inside the Oil Pan. Would not require Removal of the Tranny or Motor.

Jan 15, 2009 | 1988 Ford Bronco II

Not finding what you are looking for?
1995 Ford Taurus Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5608 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides