Question about 2000 Honda Odyssey

1 Answer

Problem 1 - while driving yesterday, tapped brakes & rpm/speed/lights/radio went dead yet the engine kept running. tapped again, same. eventually, would not return (as if i'd turned off). drove home, coasted into driveway. what would be things to check? btw, heard a clicking in a part to the upper right of engine when hood is up. clicking gone w/ full powered battery. problem 2 - making whirring sound w/ rpm. mechanic tested by taking off serpentine, sound gone, replaced tension wheel & put belt on, sound back. said it could only be alt, a/c comp, crankshaft. replaced alt w/ a salvaged part, sound still there, alt tested ok on power output. is the a/c likely? MANY THANKS!! Steve

Posted by on

  • stephen_auge Feb 11, 2010

    thanks for the solution(s). looked for fuse but had none. read online about another possible explanation... an engine control unit (ecu) regulating current may be on the fritz. advance auto checked... it said battery had 12.6 no load & loaded plus no voltage for the charging system but 1 month ago a mechanic checked it out & said the alternator was w/in the voltage spec range you stated. i think i'm going to trade it in...

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 6,826 Answers

Make sure the alternator is getting charge to the battery,if it is not,look for a fuse blown,or bad connection.Run a new wire on the back of the alternator,to the battery positive terminal.It is the large wire on the alternator,leave the one that is on there connected,just add another good size wire on that terminal,and run it to the positive side of the battery,do this if there is no charging at the battery.The noise can be any pulley making this noise.The power steering could be winning,check the fluid level in the power steering pump reservoir.If the alternator is not charging,replace it,this car has to have alternator producing 13.65 volts,to 14.25 volts,or it will have problems,such as you are having,the battery can be good,and strong,but the alternator ,still has to be charging correctly.

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the ignition timing for 2002 nissan hardbody 2000i 16v


Here are the 3 engines listed for this year. IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 2.4L SFI 4cyl

The Ignition Timing

18-22 DegreesBefore top dead center - When throttle positionsensor disconnected and using suitably programmedscan tool.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (750-850 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (700-800 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI SC 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chockdrive wheels, curb idle speed (700-800 RPM)transmission in neutral.

Jun 05, 2015 | Nissan Hardbody Cars & Trucks

1 Answer

Speedometer went haywire and car stopped


define haywire.?

dead, off, and is odometer off too?
stopped, you mean the car stalled?

when the engine stalls you see the following (driving school 101)
1: quiet , now. from engine.
2: steering and braking get harder. up to 6 times harder.
3: RPM tachometer shows 0 RPM.
4: Speed drops and lands on zero as car stops or you run out of down hill free right.

so did engine stall? does it restart,?

Nov 11, 2013 | Suzuki Esteem Cars & Trucks

2 Answers

In a 1981 dodge power ram with a 5.2l what should the timing be


5.2L 4BL 8cyl

Ignition Timing16 Degrees

Application:
With automatic transmission
Light duty

Note :
Before top dead center
*Set at warm idle speed (750 RPM)
*Distributor vacuum hose disconnected & plugged
*Transmission in drive (parking brake engaged)
Ignition Timing12 Degrees
Application:
With manual transmission
Light duty

Note :
Before top dead center
*Set at warm idle speed (750 RPM)
*Distributor vacuum hose disconnected & plugged
*All accessories off
*Transmission in neutral (parking brake engaged)

Aug 27, 2013 | Dodge Cars & Trucks

1 Answer

High rpm at highway speed


No idea why you would drive that fast,
but 2800 is about right at that speed

Did you just get the car & never own one that
went to 2800 at that speed

Tap the brake around 55 & see if the rpm goes up,
indicating that torque converter lock-up is working

Don't do that at 70 mph

Jan 29, 2013 | 2000 Mercury Sable

1 Answer

After battery in my 2001 jimmy manual 5 speed battery was run low till almost dead twice in 24 hour period, due to leaving key on too long while not running, it started after using jumper cables both...


The reset rate for vehicle computers vary by manufacturer, but 50-100 miles sounds good for the relearning process. As with the RPM's climbing unexpectedly, as a precaution I would look for a vacuum leak under your hood... it will be a hissing sound around some rubber hoses, as this can cause the RPM's to fluctuate and possibly give check engine light codes.

Oct 07, 2010 | 2001 GMC Jimmy

1 Answer

What are timing marks on 2001 kia rio 1.5 engine


3-13 Degrees
Application:
With manual transmission

Note :
Before top dead center, at specified curb idle speed.
Locate data link connector & connect jumper wire
between ground & engine test terminals.
After completing adjustment, remove jumper wire.
Curb idle speed (750 RPM) transmission in drive.

3-13 Degrees
Application:
With automatic transmission

Note :
Before top dead center, at specified curb idle speed.
Locate data link connector & connector jumper
wire between ground & engine test terminals.
After completing adjustment, remove jumper wire.
When adjusting idle speed, set parking
brake & chock drive wheels.
Curb idle speed (750 RPM) transmission in neutral

Aug 18, 2010 | Kia Rio Cars & Trucks

Not finding what you are looking for?
2000 Honda Odyssey Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...