Question about 1990 Nissan Sentra

1 Answer

Valve clearance of 12 valve engine

What is the correct clearance of intake and exhaust valve clearance of 12 valve engine.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

I do not know but give these websites a try and if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Feb 08, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Valve clearance on suzuki vitara 1999 1.6

  • Set the engine to Top Dead Centre (TDC) of the compression stroke for the cylinder to be adjusted.
  • Check the valve clearance. The valve clearance specifications are as follows:

    Intake valves: 0.005-0.007 inches (0.13-0.17mm) Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
  • After adjustment, tighten the lock nuts to 11-14 ft. lbs. (15-19 Nm).
  • Repeat for each valve to be adjusted.
  • Feb 16, 2017 | Suzuki Cars & Trucks

    1 Answer

    What is the valve clearance for intake valve and exhaust valve for mitsubishi engine 4D32?

    Please follow link to complete instuction's on the Correct way to set valve clearance on the 4D32 engine type.

    May 15, 2016 | Mitsubishi Cars & Trucks

    2 Answers

    Valve clearance 4g13

    make the engine runs for about 30minutes before adjusting the valves,
    valve clearances:
    intake valve = 0.20mm(0.008 in)
    exhaust valve = 0.25mm(0.010 in)
    for reference only when the engine is cold,
    valve clearances:
    intake valve = 0.25mm(0.010 in)
    exhaust valve = 0.30mm(0.012 in)
    engine specs: mitsubishi 4g13 1.3L (if you have same engine)

    Feb 29, 2012 | Mitsubishi Cars & Trucks

    2 Answers

    What are the valve clearance specs for a 1996 Toyota T100 v6?

    you should get haynes auto repair manul for your particular car that way you will have the correct information about that. you can get the manul at autozone or any autopart, all you need is your car info, to pick the right manual for your car, good luck

    Jul 15, 2011 | Toyota T100 Cars & Trucks

    3 Answers

    Valve clearance 4hj1 isuzu engine

    This is the specs for the 4H Diesel engine:
    Intake valves clearance cold 0.4mm(.016inches)
    Exhaust valve clearance cold 0.4mm(.016inches)

    Jan 28, 2011 | 1995 Isuzu Pickup

    2 Answers

    Procedure of tappet adjustment

    make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

    Mar 14, 2010 | 1986 Suzuki Samurai

    1 Answer

    Valve Clearance

    valve clearance, with engine hot, intake valves are .005-.006 in, exhaust valves are .011 in, if engine is cold then its intake .009-.011 in and exhaust is .007. hope this helps good luck.

    Nov 28, 2009 | 1989 Suzuki Swift

    1 Answer

    Want to know what the valve clearances are for my 1999 hyndai excel

    Adjust the jet valve clearance before the adjustment of the
    intake valve clearance.
    Jet valve clearance (hot engine)
    [Standard value]. . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

    now adjust valve clearance
    Valve clearance (hot engine) [Standard value]
    Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 mm (0.006 in.)
    Exhaust. . . . . . . . . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

    Jul 30, 2009 | 1990 Hyundai Excel

    2 Answers

    Valve clearances

    On the intake 0.0008 or 0.0020 (it's in between these 2)

    this is for the stem to guide clearance. (for the intake)

    The Exhaust 0.0018 to 0.0030 stem to guide clearance.

    Jul 10, 2008 | 1993 Nissan Pickup

    Not finding what you are looking for?
    1990 Nissan Sentra Logo

    Related Topics:

    694 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts


    Level 3 Expert

    75797 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    713 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides