Question about Ford Crown Victoria

1 Answer

Steps to replacing a fuel pump on 1992 crown vic

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Disconnect negative battery cable from battery, then unscrew fuel cap to relieve pressure, then remove bolts where filler tube connect to fuel tank, then unplug wire harness and fuel lines, then suppor tank with a jack. Then remove support straps, unscrew tank and drop tank. Then with a BRASS only punch and hammer, (so there is no sparks) knock the ring in center of tank counter-clockwise until ring is completely loose. Pull out fuel sending unit very carefully and also the pump. Disconnect pump, replace and reverse procedure to install.

Posted on Feb 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'M NOT GETTING FUEL TO THE INJECTORS ON A 85 CROWN VIC . THE FUEL PUMP AND THE RELAY HAVE BENN REPLACED WHATS THE NEXT STEP/


You will only get fuel at the injectors when cranking, the pump wont run(Usually) with just the key on. This is to prevent the pump running in a crash and feeding the engine.

May 18, 2014 | 1985 Ford Crown Victoria

2 Answers

My 1992 crown vic is not getting any gas to the injectors i think its my fuel pump i dont know how to take the pump off wat can i do and how do i take the pump off


fuel pump is in the gas tank. Have to drop the gas tank. Make sure that u run all tghe gas out before u drop the tank. Also make sure that u mark how the old pump comes out and put back the same way so the float will work. Watch for the wires on the pump that u do not break any of them.

Mar 25, 2011 | 1992 Ford Crown Victoria

1 Answer

How big is the gas tank on a 1992 ford crown vic. how many miles to the gallon. my gas gauge doesnt work. so i dont know anything about the gas.


1992 Ford Crown Vic 4.6 L V8 Automatic

Fuel tank capacity is 20 gallons (US).

Your fuel consumption will be affected by many factors, such as :
- how you drive the vehicle
- the condition and tune of the motor
- driving conditions (traffic, city use, highway use etc)
- tire pressures
- type and grade of fuel used .

It is impossible for me to estimate what fuel consumption you can expect from your own particular car without a whole lot of information.

It's unwise to run the vehicle for long with no working fuel gauge.

Dec 17, 2010 | 1992 Ford Crown Victoria

1 Answer

1992 ford crown vic working fine, next day no power to fuel pump or cut off switch


  1. Hi Domino, The fuel shut off is powered by the fuel pump relay (which is in the engine compartment fuse block) the fuel pump relay is powered by the EEC power relay(PCM relay) you will have to check for distribution and voltage. I hope this helps!

Aug 31, 2010 | 1992 Ford Crown Victoria

1 Answer

1992 crown vic cranks wont start


check fuses,
Change fuel pump.
Vitally

Sep 15, 2009 | 1992 Ford Crown Victoria

1 Answer

Crown Vic Fuel Line


I do not recommend doing this.
a 1/4 inch line has a .0491 square inch hole.
a 5/16 inch line has a .0767 square inch hole.
This would result in lowering the flow capacity of the line by over 30%.

You can possibly starve the engine of fuel causing the engine to run lean, which can result in overheating and even worse melting the tops of your pistons in the engine.

Most good automotive stores have many types of brake line and fuel line fittings and adapters you can purchase.

Good luck with your project!

Sep 09, 2009 | 1992 Ford Crown Victoria

1 Answer

Fuel pump fuse


Replace fuel pump drawing to much resistance.

Jun 19, 2009 | 1988 Ford Crown Victoria

2 Answers

We have a problem with a 1992 crown vic. It bogs


run a presher test on your fuel pump.check your fuel filter. have nice day

Apr 02, 2009 | 1992 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...