Question about 2001 Saturn S-Series

1 Answer

I need an air cleaning mounting gasket i looked every wehre no where to get one or the whole air cleaning assembly

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 200 Answers

Call a salvage yard in your area.

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seal came apart on side marker light assembly


Should be able to use clear silicone sealer for the light, you may need to take the bulb out first to vent the air inside for a good seal.
People use yellow weatherstrip adhesive for door gaskets, but the snaps help keep it in place - so the adhesive may not last long.
You might check with an auto parts store or someone who supplies body shops for a replacement strip. Most of that kind of thing is made by aftermarket suppliers.

Jul 15, 2012 | 1996 Lincoln Town Car

1 Answer

How to replace oil pan gasket


1994-96 VEHICLES
( see Figures 6 and 7 / click image for zoom )


zjlimited_1359.jpg

Fig. 6: Oil pan mounting bolt locations-1996 3.1L engine shown

zjlimited_1360.jpg

Fig. 7: Oil pan sealant application points-1996 3.1L engine shown

  1. Disconnect the negative battery cable.
It may be necessary to remove the hood, with the help of an assistant, for access.
  1. Remove the engine mount strut and A/C compressor (if equipped) and the engine mount strut bracket assemblies.
  2. Remove the electric cooling fan assemblies. -28467 and J 26462, or equivalent.
  3. Raise and safely support the vehicle. Drain the engine oil.
  4. Remove the front exhaust manifold pipe.
  5. Remove the intermediate shaft bolt/screw.
  6. Remove the oil level sensor.
  7. Remove the engine splash shield.
  8. Suitable support the drivetrain and front suspension with jack stands.
  9. Remove the transaxle mount side frame retaining nuts from the drivetrain and suspension frame assembly.
  10. Remove the engine mount side frame nuts from the drivetrain and suspension frame assembly.
  11. Unfasten the rear drivetrain and front suspension frame bolts/screws.
  12. If equipped, remove the lower drivetrain and front suspension frame bolts/screws.
  13. Remove the engine mount assembly.
  14. Remove the flywheel inspection cover.
  15. Remove the starter.
  16. Disconnect the transaxle mount assembly from the oil pan.
  17. Unfasten the side bolts and screws and the retaining bolts and screws, then remove the oil pan. Remove and discard the oil pan gasket.
To install:
  1. Clean the gasket mating surfaces.
  2. Apply a small amount of sealer on either side of the rear main bearing cap, where the seal surface on the cap meets the cylinder block. Install a new gasket on the oil pan.
  3. Position the oil pan and secure with the retaining bolts and screws. Tighten the retaining bolts and screws to 18 ft. lbs. (25 Nm) and the side bolts/screws using tool J 39505 or equivalent.
  4. Fasten the transaxle mount assembly to the oil pan.
  5. Install the starter motor.
  6. Install the flywheel inspection cover.
  7. Install the engine mount assembly.
  8. Carefully raise the drivetrain and front suspension assembly. Install the rear drivetrain and front suspension frame bolts/screws.
  9. Fasten the engine mount frame side nuts to the drivetrain and front suspension frame assembly. Install the transaxle mount frame side nuts to the drivetrain and suspension frame assembly.
  10. Remove the jackstands from the drivetrain and front suspension frame assembly.
  11. Install the engine splash shield and the oil level sensor.
  12. Install the intermediate steering shaft bolt/screw. Connect the front exhaust manifold pipe.
  13. Carefully lower the vehicle.
  14. Remove the engine support tools.
  15. Install the electric cooling fan assemblies.
  16. Install the engine mount strut and A/C compressor, bracket and the engine mount strut bracket.
  17. If removed, install the hood assembly.
  18. Fill the crankcase to the correct level. Connect the negative battery cable. Run the engine to normal operating temperature and check for leaks.
Hope this helps (remember to rate this answer).

Jun 04, 2011 | 1994 Oldsmobile Cutlass Supreme

2 Answers

95 GMC surburban keeps dying when in low rpm. I replaced the fuel filter and it ran good for a few days, then started crapping out again. I then replaced the spark plugs and wires and it ran great for...


First check for a vacuum leak. Any small loose hoses in the engine compartment? If not, suspect the idle air control valve. I have pasted test procedures for the iac below. Be careful not to confuse the tps with the iac. The tps is centered on the ybro5ttle body. The iac is more on the perimeter. An additional test I do after checking the valve is to plug it back in while it is still off the throttle body and verify that it actuates a little when the key is turned on. It should back up a tad to allow idle air through the passage for starting.

TESTING
Disengage the IAC electrical connector.Using an ohmmeter, measure the resistance between IAC terminals A and B. Next measure the resistance between terminals C and D.Verify that the resistance between both sets of IAC terminals is 20-80 ohms. If the resistance is not as specified, the IAC may be faulty.Measure the resistance between IAC terminals B and C. Next measure the resistance between terminals A and D.Verify that the resistance between both sets of IAC terminals is infinite. If the resistance is not infinite, the IAC may be faulty.Also, with a small mirror, inspect IAC air inlet passage and pintle for debris. Clean as necessary, as this can cause IAC malfunction.


Fig. Fig. 2: Using an ohmmeter, backprobe terminals of the TPS sensor to check for proper resistances



Fig. Fig. 3: The TP sensor and IAC sensor are usually located at the side of the throttle body



Fig. Fig. 4: Idle Air Control (IAC) valve wiring and terminal identification
REMOVAL & INSTALLATION

Disconnect the negative battery cable.Disengage the electrical connection.Remove the IAC valve. On thread-mounted units, use 1 1 / 4 in. (32mm) wrench and on flange-mounted units, remove the screw assemblies.Remove the IAC valve gasket or O-ring and discard it.To install:
Clean the old gasket material from the surface of the throttle body assembly on the thread mounted valve. On the flange-mounted valve clean the surface to ensure proper O-ring sealingInstall the valve with a new gasket or O-ring. Tighten the thread mounted assembly 13 ft. lbs. (18 Nm) and tighten the flange mounted attaching screws to 28 inch. lbs. (3 Nm).Engage the electrical connector to the IAC valve.Connect the negative battery cable.ecd523da-60e9-4928-9b74-9d90b47be2df.gif0996b43f802319fe-tedh1mdkpnm2cwqabpnjpaem-4-2.gif0996b43f802319ff-tedh1mdkpnm2cwqabpnjpaem-4-3.gif0996b43f80219b22-tedh1mdkpnm2cwqabpnjpaem-4-4.gif

0996b43f802319ff-tedh1mdkpnm2cwqabpnjpaem-4-3.gif


0996b43f802319fe-tedh1mdkpnm2cwqabpnjpaem-4-2.gif


ecd523da-60e9-4928-9b74-9d90b47be2df.gif

Jul 21, 2017 | 1995 GMC Suburban

2 Answers

How do you remove the headlights off a Pontiac grand am 2004


Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:
  1. Open the hood.
  2. Remove the front air deflector.
  3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
  4. Lift up the headlight retainers to release the housing.
  5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
  6. Disconnect the wiring harness from the headlight assembly.
  7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
  8. Remove the bulb(s)/socket(s) from the headlight assembly.
To Install:
  1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
  2. Connect the wiring harness to the headlight assembly.
  3. Position the headlight assembly to the mounting panel.
  4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
  5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
  6. Install the front air deflector.
  7. Close the hood.
prev.gif next.gif

Feb 02, 2011 | 2004 Pontiac Grand Am

1 Answer

Thermostat replacement 2002 rendezvous


Thermostat Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Drain the coolant below the level of the thermostat.
  2. Remove the air cleaner and duct assembly.
  3. Remove the exhaust crossover pipe.
  4. Disconnect the radiator hose from the thermostat housing. gm_mv_ven_tstat.gif

  5. Remove the mounting bolts and remove the thermostat housing.
  6. Remove the housing gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine. NOTE: Apply RTV sealer to the thermostat housing bolt threads.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Install the exhaust crossover pipe.
  5. Install the air cleaner and duct assembly.
  6. Fill the cooling system.
  7. Check the cooling system for leaks.
3.6L Engine To Remove:
  1. Remove the air cleaner.
  2. Remove the throttle body.
  3. Remove the heater pipes.
  4. Remove the coolant inlet pipe. Thermostat 3.6L gm-03-36-2447.gif

  5. Remove the thermostat mounting bolts and remove the thermostat.
  6. Clean the thermostat and heater pipe mating surfaces.
To Install:
  1. Place the thermostat in the housing with a new gasket.
  2. Install the thermostat and gasket on the engine with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Install the coolant inlet pipe.
  4. Install the heater pipes.
  5. Install the throttle body.
  6. Install the air cleaner.
  7. Fill the cooling system and perform a leak test.
prev.gif next.gif

Dec 19, 2010 | 2002 Buick Rendezvous

1 Answer

What do i do when its over heating? how do i install thermostat?


Thermostat Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Drain the coolant below the level of the thermostat.
  2. Remove the air cleaner and duct assembly.
  3. Remove the exhaust crossover pipe.
  4. Disconnect the radiator hose from the thermostat housing. gm_mv_ven_tstat.gif

  5. Remove the mounting bolts and remove the thermostat housing.
  6. Remove the housing gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine. NOTE: Apply RTV sealer to the thermostat housing bolt threads.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Install the exhaust crossover pipe.
  5. Install the air cleaner and duct assembly.
  6. Fill the cooling system.
  7. Check the cooling system for leaks.
3.6L Engine To Remove:
  1. Remove the air cleaner.
  2. Remove the throttle body.
  3. Remove the heater pipes.
  4. Remove the coolant inlet pipe. Thermostat 3.6L gm-03-36-2447.gif

  5. Remove the thermostat mounting bolts and remove the thermostat.
  6. Clean the thermostat and heater pipe mating surfaces.
To Install:
  1. Place the thermostat in the housing with a new gasket.
  2. Install the thermostat and gasket on the engine with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Install the coolant inlet pipe.
  4. Install the heater pipes.
  5. Install the throttle body.
  6. Install the air cleaner.
  7. Fill the cooling system and perform a leak test.
prev.gif next.gif

Sep 18, 2010 | 2002 Pontiac Aztek

1 Answer

NEED HELP WITH TORQUE SPECS ON 1998 CHEVROLET SURBURBAN CYLINDER HEADS 5.7


Cylinder Head Removal & Installation 5.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the engine coolant.
  3. Remove the air cleaner assembly.
  4. Remove the upper radiator hose.
  5. Remove both heater hoses.
  6. Disconnect spark plug wires at distributor cap.
  7. Remove distributor cap.
  8. Remove the coolant bypass hose from the water pump.
  9. Remove the drive belt. NOTE: It is not necessary to evacuate the A/C refrigerant.
  10. Remove the A/C compressor from the mounting bracket and set it aside.
  11. Remove the wiring bracket from the rear of the cylinder head.
  12. Disconnect the accessory bracket and slide forward.
  13. Remove the upper and lower intake manifold.
  14. Remove the exhaust manifolds.
  15. Remove the valve rocker arms and pushrods.
  16. Remove the power steering pump pulley.
  17. Disconnect the electrical connector from the power steering pump.
  18. Remove nuts attaching the power steering pump to the engine.
  19. Remove power steering pump mounting bracket bolts and nut.
  20. Slide power steering pump/bracket assembly forward and remove stud.
  21. Set power steering pump/bracket assembly aside.
  22. Disconnect the wiring bracket from rear of the right cylinder head.
  23. Remove the generator.
  24. Remove the oil indicator tube bracket bolt.
  25. Remove the generator mounting bracket.
  26. Remove the sixteen cylinder head bolts.
  27. Remove cylinder heads and gaskets.
  28. Clean all sealing surfaces.
To Install:
Right Side NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the generator mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the generator mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the generator.
  16. Install the oil indicator tube bracket bolt.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.
Left Side To Install:
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the power steering pump mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the power steering pump pulley.
  16. Connect the electrical connector to the power steering pump.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.

Aug 31, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

Can i print a diagram for removal of my waterpump


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Drain the engine cooling system.
  4. Remove or disconnect the following:
    NOTE On some engines, the pump retaining bolts will vary in size and thread. Be sure to note the positioning of all bolts during removal to assure proper installation.


    Air intake assembly Mass Air Flow (MAF) sensor Upper fan shroud Drive belt Fan and clutch assembly Water pump pulley using special tool J 41240 Coolant hoses Water pump
  5. Clean gasket mounting surface.

    0900c15280227aee.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Removing the water pump pulley using special tool J-41240


    0900c15280227aef.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Water pump mounting-2002 shown

Jan 29, 2009 | 1999 Chevrolet Astro

1 Answer

1998 dodge avenger tranmission control solenoid


Below the link for Chrysler/Dodge auto-transmission manual
http://www.scribd.com/doc/7095618/545rfe-Transmission-Manual

Solenoid mounts outside the transmission, so you do not need to remove the transmission to install. It should be located between fuse box and air filter housing on the top of transaxle case and right next to transmission controle module.
I hope his step by step procedure will work for you. It is not hard at all to replace the solenoid. There are three 10mm bolts. You will also need to remove the input speed sensor. One thing to look out for is not bending the gasket when installing the new solenoid:
  1. Disconnect battery negative cable.
  2. Remove air cleaner assembly.
  3. Remove electrical connectors for transmission control module (please refer the manual I send you and autozone.com website).
  4. Remove the Transmission Control Module
  5. Disconnect and remove the input speed sensor
  6. Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
  7. Disconnect the solenoid/pressure switch assembly connector.
  8. Remove the three solenoid/pressure switch assembly-to-transaxle case bolts
  9. Remove solenoid/pressure switch assembly and gasket

Keep everything clean to prevent foreign materials to go inside
  1. Install solenoid/pressure switch assembly to case using a new gasket
  2. Install bolts and torque to 13 N·m (110 in. lbs.)
  3. Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
  4. Uncap and install transmission oil cooler lines.
  5. Install input speed sensor and torque to 27 N·m (20 ft. lbs.)
  6. Install Transmission Control Module
  7. Install air cleaner assembly.
  8. Connect battery negative cable.

P.s. 1. You can fine some clips on YouTube.com at least for similar cars
2. Also at Autozone.com you can find the component location for your car and repair guide
3. Also there is a link for Mitchel1 online manual useb by US mechanic 1 week subscribtion is
11.99 , 1 month 16.99
http://www.2carpros.com/kpages/auto_repair_manuals.htm
Let me know if you need more info
Good Luck and happy fixing

Jan 22, 2009 | 1998 Dodge Avenger

2 Answers

2003 hyundia accent 1.6


The MAF is mounted in the intake air hose of the air cleaner assembly.
The MAF is mounted in the intake air hose of the air cleaner assembly.
The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles this sensor is combined wit the ATS sensor.
The MAF is mounted in the intake air hose of the air cleaner assembly.
This sensor is located in the air intake plenum assembly. It is combined with the IAT sensor.
The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles it is combined with the IAT sensor.

Oct 08, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
2001 Saturn S-Series Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...