Question about 1992 Jeep Cherokee Sport

2 Answers

WHAT BOLTS DO I LOOSEN TO GET FAN BELT ON 1992 JEEP CHEROKEE 6 CYLINDER. I HAVE THE BELT ON PRPERLY AROUND THE 1ST 5 PULLEYS. BUT THE UPPER RIGHT PULLEY HAS TO BE LOOSENED IN SOME WAY TO GET BELT ON. HOW DO I LOOSEN IT TO GET IT TO MOVE TO THE LEFT TO GET BELT ON????

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 44 Answers

CHECK THE IDLER PULLEYS,YOU WILL FIND ONE THAT HAS A BOLT BEHIND IT.YOU HAVE TO LOOSEN THE NUT THAT HOLDS THE PULLEY,THEN SLACK THE ONE TO LOOSEN THE PULLEY.

Posted on Feb 08, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 42 Answers

The power steering pump has a seperate adjuster bolt ont the bottom left of the pump if you loosen this off then loosen the pulley bolt it iwill move in to allow for the belt then tighten the adjuster bolt till the tension on the belt only allows for a 1/2 inch movement up or down then tighten pulley bolt
not the pump may be stiff to move at first

Posted on Feb 08, 2010

  • Thomas Moore
    Thomas Moore Feb 08, 2010

    the power steering pump has a seperate adjuster bolt ont the bottom left of the pump if you loosen this off then loosen the pulley bolt it iwill move in to allow for the belt then tighten the adjuster bolt till the tension on the belt only allows for a 1/2 inch movement up or down then tighten pulley bolt

    not the pump may be stiff to move at first

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace fan belt.


loosen the belt by pulling on the belt tensioner remove the belt remembering the way it goes around the pulleys place the new belt on in the same routing the old one was release pressure on the tensioner and run the engine until warm the belt will stretch and you will need to re adjust tension until about 1/24 of play is reached

Jan 14, 2011 | 1994 Jeep Cherokee Country

1 Answer

How do you tighten belt on a cherokee


To make a belt adjustment, you need to loosen the bolts on the power steering pump. Under the pump, you will see a long bolt that runs sideways. You loosen the bolt that locks that bolt from turning,(on the end nearest the block)then turn it till the pump moves and tightens the belt. (1" deflection at the longest run is about right). Then tighten up everything you just loosened.

Nov 02, 2010 | 1992 Jeep Cherokee Sport

2 Answers

Need diagram to put timingbelt on 2001 kia sportage


prev.gif next.gif Timing Belt Removal & Installation SOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
  4. Remove upper radiator hose.
  5. Remove fan clutch assembly bolts.
  6. Remove 5 cooling fan shroud bolts.
  7. Remove fan shroud and fan as an assembly.
  8. Loosen alternator mounting bolts and remove drive belt from pulley.
  9. Remove fan pulley.
  10. Remove 4 cooling fan assembly bolts.
  11. Remove cooling fan assembly.
  12. Remove 4 bolts and upper timing belt cover.
  13. Remove 2 lower bolts and lower timing belt cover.
  14. Loosen adjusting bolt and remove A/C belt.
  15. Remove alternator belt.
  16. Loosen power steering pump lock bolt and mounting bolt.
  17. Remove drive belt from crankshaft damper. Camshaft timing marks kia-03-20-7032.gif

  18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  19. Remove 5 bolts and remove damper.
  20. Remove timing belt guide from timing belt pulley.
  21. Loosen tensioner lock bolt.
  22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
  23. Remove timing belt.
To Install:
Timing belt pulley timing marks kia-03-20-7035.gif

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks kia-03-20-7032.gif

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation kia-03-20-7036.gif

  1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
  2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
    Do not turn crankshaft counterclockwise.
  3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
  4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
  5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
    • Deflection should measure 0.43-0.51 inch (11-13 mm)
    NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
  6. Install timing belt guide.
  7. Install crankshaft damper pulley.
  8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
  9. Install power steering pump drive belt.
  10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
  11. Install alternator drive belt.
  12. Install A/C drive belt.
  13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
  16. Install fan pulley.
  17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
  18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
  19. Adjust alternator belt tension and tighten alternator mounting bolts.
  20. Install upper radiator hose.
  21. Install fresh air duct.
  22. Connect battery negative cable.
  23. Refill/bleed cooling system.
DOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
  4. Remove 4 thermo-modulated fan shroud fasteners.
  5. Remove generator drive belt.
  6. Remove fan pulley (located above crankshaft pulley).
  7. Remove 4 bolts and splash shield (located under front of vehicle).
  8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal kia-03-20-7097.gif

  9. Remove 5 bolts and upper timing belt cover.
  10. Remove 2 bolts and lower timing belt cover.
  11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
  12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
  13. Remove timing belt.
To Install:
Crankshaft match marks 79245g25.gif

  1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks 79245g28.gif

  2. Align marks on camshaft pulleys with alignment marks on seal plate.
  3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  4. Loosen tensioner lock bolt.
  5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
    • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
    NOTE: Replace tensioner spring if timing belt deflection is excessive.
    Timing Belt Installation kia-03-20-7097.gif

  8. Install lower timing belt cover.
  9. Install upper timing belt cover.
  10. Install power steering drive belt and adjust belt tension.
  11. Install fan pulley.
  12. Install generator drive belt and adjust belt tension.
  13. Install A/C drive belt and adjust belt tension.
  14. Install splash guard.
  15. Install fan and fan shroud.
  16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  17. Install fan shroud mounting bolts.
  18. Install fresh air duct.
  19. Connect hose to resonance chamber.
  20. Connect battery negative cable.

Aug 02, 2010 | 2001 Kia Sportage

2 Answers

Must i remove the radiator, the grill, and the fan, in order to change the fan (serpentine) belt on the 1996 Grand Cherokee Laredo?


Absolutely not.. It will come out by releasing tension on the belt and working it around the pulleys..It's tight but it will come.

Jul 29, 2010 | 1996 Jeep Grand Cherokee

1 Answer

A new tensioner was fitted, it was rattling then


YEP SOME JEEP 6 CYLINDER ENGINE BELT TENSIONER NOT AUTOMATIC.YOU HAD TO ADJUST BELT TENSION BY LOOSEN THE POWER STEERING PUMP BOLTS AND TURN THE TENSIONER ADJUSTING BOLT TO TIGHTEN OR LOOSEN THE DRIVE BELT.IF YOU HAVE THE AUTOMATIC BELT TENSIONER.EITHER YOU ARE GETTING THE WRONG ONE OR BELT TOO BIG.IF IT WAS ME TAKE TO ANOTHER GARAGE.

Jun 13, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I need the drive belt configuration for a 1988 Jeep Cherokee.


To replace belt, first loosen the pivot and slide bolt on the steering pump, then use the jack bolt below the pump to move it. Belt goes (ccw) around outside of ps pump, under idler pulley, over a/c compressorover alternator over fan pulley, over crank pulley over water pump and back to the ps pump. best bottom (grooved area) should match with any pulley with grooves, back of belt should contact smooth pulleys. 9example...grooved part contacts ps pulley, smooth back goes under idler pulley) When finished the water pump should spin ccw (I've seen them put on incorrectly so it turns backwards) Tighten jack bolt till the long strech of belt is giving about 1" deflection, then lock pivot and slide bolts down.

Nov 28, 2009 | 1988 Jeep Cherokee

1 Answer

Serpentine belt diagram for 2000 jeep grand cherokee 6 cylinder


Around the outside of power steering pulley,under idler,over a/c comp,around alternator,over fan pulley, around crank pulley, over water pump. The backside of the belt contacts the idler, fan and water pump.

Sep 28, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Replace serpentine belt for 6 cylinder 4wd


Loosen the power steering pump rear mounting bolts, pivot bolt and lock nut and then loosen the power steering pump adjusting bolt. Slip the belt on and tighten the adjusting bolt until you can push the belt in about one inch midway between the A/C and alternator pulleys. Then tighten the lock nut, pivot bolt and mounting bolts and that's it.

It helps to diagrams to go with the instructions. Get yourself factory service manual, promanuals.net has them for around 20$ or so.

Sep 23, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

I need a new timming belt on a 01 kia sephia how do i change it


Hi there,

Below are the procedures to remove the timing belt...

1. Disconnect negative battery cable.

fd440e5.jpg
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt.

1d207cf.jpg

4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts.


077a275.jpg

6. Remove water pump pulley.

2bc0452.jpg


7. Remove crankshaft pulley and timing belt guide plate.



8619b52.jpg


8. Remove upper and lower timing belt covers.


c250533.jpg


9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.


213d3a1.jpg




10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned with mark on cylinder head cover.


Do not move camshaft or crankshaft once timing marks have been correctly positioned.



a3188ba.jpg



11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.


12101a7.jpg

14. Remove timing belt.



Regards,
Jeep Brainy

Sep 20, 2009 | 2001 Kia Sephia

1 Answer

HOW DO I CHANGE THE WATER PUMP ON A 99 JEEP GRAND CHEROKEE ?


At least you have the 4 liter 6. Once you get all the **** out of the way its like replacing a W/P on an "old school" engine, very much like a Ford or Chevy straight 6. 1) Remove radiator top retainer (the metal U that looks like its the top of the radiator (#13 or 14mm sockets I think). 2) To completely get if off you also have to remove the grill (4-6 phillips screws), then 3) unbolt it from the tubular bumper retainers underneath the grill. 4) DO NOT remove the latch cable - no need. 5) Remove the top bolts holding down the fan shroud. Lift the shroud off its bottom "tabs" and push over the fan. 6) Using #10mm socket remove fan from fan clutch, then remove bolts holding fan clutch onto water pump pulley. 7) Pull out shroud, then fan, then fan clutch. Be very patient, lots of wiggling may be needed. 8) Locate belt tensioner on idler puller below the Power steering pump. Losen very little the pulleys center bolt (10mm), then use a 10mm w/entension to losen the pulley's tension (use counter clockwise/normal rotation to losen). 9) Draw a diagram of the belt routing - you will Never remember it correctly otherwise. 10) Tap the w/p pully and pull if off - do not hit radiator fins! 11) Drain the radiator (clockwise/right rotation opens petoc from factory radiators - counterclock used on aftermaket rads). 12) Remove lower raditor hose at radiator, then at pump (it will be a challenge). 13) Remove upper radiator hose from rad and from thermostat housing. 14) losen the Rubber heater hose from the metal hose screwed into the W/P. 15) Remove 4 bolts from W/P (13 or 14mm I think). The one at the 4oclock position is longer than the others. One is hidden at 6oclock.
16) Remove 2 bolts (14-15mm??) on bottom of Power Steering mount - these go through the W/P case to the block. You may also need to losen the top PS bolts so the PS Bracket can be loose at the W/P case. 17) Wiggle the W/P out from under the PS bracket. and pull off. (16b if needed, remove the upper idler pulley near the A/C unit.) 18) Remove the Thermostat (upper hose return) housing. Scrape off old gasket. Replace with 160deg or 190deg thermostat. Use silicone on gasket. 19) Carefully use a 17 or 19mm box wrench to remove the metal heater hose return line from the upper part of the old water pump. Coat threads with spark plug thread antiseize and screw onto new W/P. 20) Install new W/P gasket w/silcone, be careful to Not block the water holes. 21) Slide W/P under the P/S bracket and jiggle into place. Hand thread one of the top bolts to hold the W/P in place. 22) Insert the P/S bracket bolts and lightly tighten. 23) Jiggle W/P around and insert other bolts, start with the 6oc hidden bolt. Add remaining bolts and tighten to 25 or 250?ftlb (about 3/4 past socket-snug). 24) Tighten ALL P/S bolts. 25) Adjust metal heater pipe. Reinstall rubber heater hose. 26) Reinstall W/P pulley and Fan clutch, and upper idler if it was removed. 27) Thread NEW Belt on pulleys. 28) Tighten tension on idler. Tighten idler axle bolt. 29) Install lower rad hose. 30) Slide shroud over pulleys. 31) Install fan on clutch. 32) Clip shroud retainer bolt mounts back on top of radiator. 33) Install shroud. 34) Connect upper hose. 35) Reinstall radiator retainer. 36) Bolt retainer to Tubular bumper mounts. 37) Reinstall grill. 38) Wonder where the extra bolts etc are supposed to go. 39) Cuss - pray -cuss - pray. 40 ) sip some beer. 41) carefully inspect everything to ensure its back to the way it looked before (several pictures from a digital camera taken during the disassembly will help). 42) Close the rad petok. 43) Add 1 gallons of antifreeze. 44) Start engine and add another gallon of A/F. 45) Turn heater controls to HOT inside (no need for fan). 46) Water guage should show 180 to 210F. 47) Add 1 gallon of water. 48) Install New 18PSI rad cap. 49) Turn off engine and add water or A/F to overflow tank. 50) 1 hour later open Cap to see if level has settled. Add Water as needed to fill rad.

Dec 24, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...