Question about 2000 Jeep Grand Cherokee

1 Answer

Hub bearing possibly needs replaced. How is it done and how much should it cost. 2000 grand cherokee limited 4.0 inline 6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

Timken bearing assembly is what you need. They actually make this all sound so difficult but let me tell you how I just did the same job on my Murano 06 AWD that uses the same type of assembly.
Remove the axle bolt then the wheel, caliper & bracket to remove the rotor. Support the caliper by hanging it from the the strut spring. From the back side, you should be able to remove the speed sensor and if on that model the bolts come froom the back side, there should be just enough room to remove them. that is what holds the hub assembly in place, these aren't pressed into the vehicle, just mounted. I used an axle puller to remove the hub assembly once all of he bolts were loose & it wasn't necessary to remove the ball joint or axle. You need to push the axle through the hub assy & there is a rental tool you can get for that. (autozone free rental) There was not any excessive pulling to remove the assembly, just tap, tap, tap & it was free, ready for the other to be installed. There is the possibility that you would have to drop the lower ball joint & tie rod end to get access but I didn't have that problem & I looked at your bearing, it looks identical. Cost: That's really tough since everyone wants to make their weeks payroll on whatever customers happen to show up. It took me 2 1/2 hour to do this myself on both front wheels with a HD Floor Jack and the tools mentioined Plus my good tool collection. Shouldn't be that much since they don't have to even press the bearing in or out or pull the axle. Good luck.

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is a 1995 jeep grand cherokee limited v8 vs. inline 6 transmission interchangeable?


No sir they will not interchange. i worked at a transmission shop for 7 years. the inline 6 has a 500 trans in it and the v8 has a 518 trans in it. the bellhousings are different.

Jan 03, 2014 | 1995 Jeep Grand Cherokee

1 Answer

Oil leaks on my jeep grand cherokee 2000


Most common are valve cover gaskets worn out...especially the inline 6 cylinder...inspect the oil pressure sending unit located beside the oil filter...these are the most common and least costly fixes...Hope this helps.

Aug 03, 2012 | 2000 Jeep Grand Cherokee

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

2 Answers

How to replace spark plugs on 2000 jeep cherokee classic 6 cyl.? Also does 2000 cherokee have inline fuel filter?


TO REPLACE SPARK PLUGS YOU REMOVE COIL PACK MOUNTING BOLTS THEN REMOVE THE COIL PACK WITH BOOT OVER THE SPARK PLUG.YOU HAVE 6 INDIVIDUAL COIL PACK TO EACH CYLINDER. YOU NEED A 3/8 RATCHET WRENCH - LONG 3/8 EXTENSION -SPARK PLUG SOCKET - SPARK PLUG GAUGE.AND TORQUE WRENCH.THE 2000 MODEL JEEPS FUEL FILTER INSIDE THE TANK.1993 - 1996 MODEL JEEPS FUEL FILTER LOCATED LEFT SIDE OF THE VECHICLE NEAR THE FUEL TANK.

Jul 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

1999 Jeep Grand Cherokee overheated


You probably messed up a rod or caused piston damage your going to need more than a head gasket usauly when you over heat a car you causing the pistonts to expand more then they need to causing scouring and exsisive piston ware by the sound of it and the year your better off replacing the whole motor or completely rebuilding the old one wich will cost more then a use motor! good luck!

Sep 12, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Grinding sound near lower front end of jeep


Might want to chk. the axel, or maybe wheel bearing, or caliper hanging up. Sounds more like axel or bearing bad.

Mar 28, 2009 | 1990 Jeep Cherokee Limited

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...