Question about 1999 Ford Ranger SuperCab

1 Answer

Lookking for diagrams on a 99 ford contour on how to replace water pump

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Expert
  • 262 Answers

Lookking for diagrams on a 99 ford contour on how - 185c138.gif

  1. Disconnect the battery ground cable.
  2. Drain the cooling system.
  3. Lower the vehicle.
  4. Remove the water pump drive belt tensioner.
  5. Raise and support the vehicle. NOTE: Remove and discard the water pump gasket.
  6. Remove the water pump
    1. Remove the eight bolts.
    1. Remove the pump.

Posted on Mar 21, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Power steering went out on 03/99 ford contour-- no fluid leak

Could be the pump or rack and pinion. Pumps usually whine real bad before dieing(especially when turning). The rack can blow a seal and die all of the sudden.

Jun 10, 2015 | 1999 Ford Contour

1 Answer

Replace water pump on 99 contour svt 2.5l

posted to 2010 ,
is this a DIY question? or just trying to guess labor hours?
replacing any water pump is the same on most engines
only gaining ACCESS IS THE TRICK.

so RTM , read the FSM it covers the pump, every step'
or login to its there. too.
how to fish.....

click engine cooling.
click water pump, BINGO. you are ENABLED.
FORD car posted to Chevy, way to go..... huh>
2.5 L Duratec V6
1999 Ford.
this pump has TTY bolts (use only once,) torque to yield. google it.
  1. Disconnect the negative battery cable.
CAUTION NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant.
  1. Drain the engine cooling system.
  2. Remove the water pump pulley shield.
  3. Remove the water pump drive belt.
  4. Remove the water pump inlet and outlet hoses from the water pump.
  5. Remove the three water pump to left cylinder head retaining bolts.
  6. Remove the water pump and water pump housing from the vehicle.
  7. Remove the water pump to water pump housing retaining bolts and separate the water pump from the water pump housing.

to see install, log in.. and read.

Jun 18, 2014 | 2010 Chevrolet HHR

1 Answer

Need to know inside fuse panel for 99 contour 2liter diagram of what fuse is for what

The Owner's Manual has a diagram in it. If you don't have that, then a repair manual (a Chilton's or similar will do fine) has it, too. Most dealerships can print out a fuse panel diagram for you, or you can do a Web search for "1999 Contour fuse panel diagram" and you will find a number of them.

Mar 28, 2013 | 1999 Ford Contour

1 Answer

Where is the water pump? I need a print out of the motor.

This is a photo of the water pump on the 2.0L engine.

These are diagrams of the water pump, and where it's located on the 2.5L engine.



Feb 07, 2011 | 1999 Ford Contour

1 Answer

I need a fuse box diagram(s) for a '99 Ford Contour V6 2.5 L

I suggest check in this link 1999-Ford-Contour-Owners-Manual (page 141 and next).

I hope helps (remember to rate this answer).

Oct 14, 2010 | Ford Contour Cars & Trucks

1 Answer

How to replace water pump on 1998 ford contour?

remove the three bolts from the water pump pully....then remove the water pump...once the pump is out you will have to rotate the pump 180 degrees to get it out of the engine compartment....when you go to install the new one use a tiny bit of silocone to hold the rubber gasket in place so your not pulling your hair

May 06, 2010 | 1998 Ford Contour

1 Answer

I need to know where the a/c low side line is on a 99 contour

the r-134a kits they sell today will only fit on the low side. they are usually located toward the front by the radiator

Apr 12, 2010 | 1999 Ford Contour

1 Answer

Need the timing marks for 99 ford contour

There are no marks. You need to remove #1 spark plug. Bring the piston up on TDC (all the way up). Then remove valve cover. On the drivers side of the camshafts you will see a slot ground into the ends. The slots are off center of the camshft. There is a tool to fit into the slots tieing both cams at the same time. Once the tool is installed and the #1 piston was up before you locked the cams you can remove the T-belt for replacement & water pump replacement.

Sep 08, 2009 | 1999 Ford Contour

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

855 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides