Question about Dodge Caravan

1 Answer

What to get fixed when my vans 6 cylinder misfires

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 42 Answers

This is a good indication of bad sparkplugs so i suggest you do a full tune up to correct this.this usually includes plugs wires cap rotor and pcv and fuel filter now this is dependant on the year your van man not have all this stuff in witch case you may be requred to replace a coil pack

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Miss fire #6 cyl 2000 dodge 3500 van 5.9 egine


100 PSI is way to low, I think you have a burnt valve. Check the cylinder compression on all cylinders, no cylinder should be 5% lower than the highest cylinder pressure measured or the engine will run rough or misfire.

Jan 31, 2017 | 2000 Dodge Ram 3500

1 Answer

Have a misfire in cylinder 6 changed all coil packs all spark plugs stills says cylinder 6 misfire


A misfire could be caused by almost anything, spark--fuel--compression. Did you check for spark at number 6? All electrical components have voltage and ground, if problem on wiring circuit, replacing the component won't fix it.
Also, check for fuel injector pulse--proper fuel pressure and cylinder compression.
I don't know year--make--model, it didn't post for some reason?

May 16, 2016 | Cars & Trucks

2 Answers

How to fix diagnostic code for 1999 vw passat po304 po305 po306


Hi. You have misfires on cylinders 4, 5 and 6. If there are no faults on cylinder 1, 2 and 3 then I would check the power to the left bank injectors. Also check spark plugs and ht leads. If there are running issues then this should be an easy fix. If the faults are very intermitant then it can be a bit tricky to isolate.

May 18, 2014 | 1999 Volkswagen Passat

2 Answers

2004 trailblazer code po306 and we changed out plugs, coil and still po306


Diagnostic Test Code (DTC) P0306 is defined by SAE J2012 (REV, DEC 2007) as "Cylinder 6 Misfire Detected".

To put it plain and simple, there is a problem with cylinder #6 in your engine that is causing it to misfire.

Misfires can be caused by several things. One of the things that must be understood is that a misfire is simply one or more cylinders that are not producing the power that they should. - especially when compared to other cylinders in the same engine.
The things that can cause this include, but are not limited to:
> Ignition system
> Fuel delivery system
> Fuel injection system
> Cylinder compression (which can be affected by many of the things below)
> blown head gasket
> Burned or bent valves
> Vacuum leaks
> Faulty wiring
> cracked piston or broken piston rings
> Restricted exhaust
> malfunctioning Powertrain/Engine Control Module (PCM or ECM)


To fix the code, you must first diagnose to determine which of these things is causing the misfire, then repair accordingly.

Mar 23, 2012 | Chevrolet TrailBlazer Cars & Trucks

2 Answers

1997 Town And Country LXi 3.8 V6 178,000 Miles Car had ticking sound, sounded like a lifter. Car ran without issue (stalled maybe once a month) for three months. Now the check engine light has come on...


THE 3.8 ALWAYS HAS A TICKING NOISE IT CAME FROM THE FACTORY WITH A UNBALACED CRANK ALL OF THEM DO IT,MISFIRE IS PROBABLY DO YOUR YOUR COIL PACK OR WIRES.










TIM

Feb 15, 2011 | 1997 Chrysler Town & Country

2 Answers

2002 ford escape 3.0L DTC P0305and P0306 what would you ck


P0305 - Cylinder 5 Misfire Detected
P0306 - Cylinder 6 Misfire Detected

When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the Crankshaft Position (CKP) sensor signal to vary, The Powertrain Control Module (PCM) or Electronic Control Module (ECM) can determine that a misfire is occurring.

When is the code detected?
- Engine Cylinder #5 and #6 is Misfiring.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/loss of power
- Hard start
- Engine hesitation

Possible Causes:
- Improper spark plug at cylinder #5 and #6
- Insufficient compression at cylinder #5 and #6
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #5 and #6
- Fuel injector #5 and #6 may be faulty
- Intake air leak at cyli

Possible Solution:
- Perform Injector Service
- Replaced Spark Plug #5 and #6
- Replaced Injector #5 and #6
- Replaced Ignition Coil #5 and #6

Hope helps.

Jan 02, 2011 | Ford Escape Cars & Trucks

1 Answer

1998 Chev Astro 4.3L AWD. Rough idle & misfire Cylinder 6


Hi, the 4.3 liters have an injection system on them that can leak and will show up as a misfire. it is common but elusive to find. you might consider taking the van to a repair shop to have the problem diagnosed and go on from there.

May 22, 2010 | 1998 Chevrolet Astro

3 Answers

#5 cylinder misfire


I have a corolla and had #4 cylinder misfire also diagnosed at autozone. After changing the spark plugs, problem persisted, along with the same error code, so they recommended changing the spark plug wires, and that is what fixed it. I would have changed the rotor cap too, but was low on dough. Glad that was not the problem.

Dec 29, 2008 | 2007 Mazda MPV

2 Answers

Need know which cylinder is number one on 2000 ford windstar 3.8


#1 plug is the 1st plug on passenger side by firewall

Nov 15, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...