Question about 1986 Ford Crown Victoria

1 Answer

We have a water leak at the rear of the intake manifold. It's either coming from the hoses or there is a leak in the tubing coming from the intake manifold to the hoses connecting to the heater core. How would we remove the tubing rail?

Posted by on

  • bowhuntr561 Feb 08, 2010

    1986 Crown Vic with a 5.0 Liter

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What kind of car?

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coolant leak between engine and trans lower portion near oil pan do any coolant tubes or hose run in that area from water pump to radiator


There are cylinder block core cleanout casting plugs back there, one or more could be rusted out. Also make sure the coolant is not coming from up top like at the rear of intake manifold.

May 09, 2016 | Cars & Trucks

Tip

Intake Manifold gasket replacement and/or leaking= Ford


Intake Manifold gasket~

Replacing intake manifold gasket:
Replacing the intake manifold gasket, I used the tube kind, it's a make it youself for about $6 (it's blue and the consistancy of toothpaste) follow directions carefully! You can get a tube at Autozone or any car parts store. Has been working great. Just ask the cashier for the make it yourself kind of intake manifold gasket. Sorry, I don't remember the name of it, it's been that long...lol...

As for the Intake Manifold leaking coolant....It could, but shouldn't. One of the largest problems I've seen for coolant to leak out the Intake Manifold has been due to pressure in the system somewhere... Check the classic area:
Water pump- look for either water seapage and/or coolant. You'll know if it is because you will see real water either coming out of the water pump leak hole or under the thermostat. Most of the time coolant will pool where your heater hose runs in the intake manifold.

Mentioning heater hose. Check for leaks, holes, and/or cracked heater hoses. In-addition to the water pump, heater hoses...Check the transmission system, exhaust system, fuel system, radiator system, A/C system, secondary fan (located above the water pump housing), and thermostat.Also, check all electrical connections....Hummm....This is almost the entire workings of the vehicle.

NOTE: "It seems to be an infinity kinda thing... Once one thing starts to fail and is ignored, you are bound to be fixing a chain of event failures. Therefore, Do not ignore even the smallest problem or you'll be bound for life in repairs...."

on Jun 25, 2010 | Ford Expedition Cars & Trucks

1 Answer

Coolant line under intake is leaking 95 town car


95 Lincoln town car coolant leak under intake SOLUTION EASY

Ok this is a 4" piece of hose leaking on a tube that runs under the intake manifold and fastens to the rear of the engine with 2 small bolts that are very hard to get to. The heater core hooks up to this tube with a 5/8 hose that's 3/4 on the other end going into the heatrer core.
Solution:
remove alternator
see clamp on hose?
remove it.
If you can't remove it, clamp vice grips on it and take a steak knife and cut through the hose towards the rear of the engine. Now with large screw driver pry the hose and clamp off the nub on the rear of the water pump housing. You may have to move the tube and remaining hose out of the way first. Just stick your hands in there and force it out of the way. Now you have a clean nub to hook a 5/8 bypass hose to. Here's where you get it. Go back to the heater core and and remove the hose that connects to this tube that runs under the intake. Just cut it where it hooks to the tube and remove it carefully from the heater core because this is now your needed bypass hose. Now with a couple feet of 3/4 hose and a coupler you have all you need to reroute this water outlet around the engine to the heater core. Take your hose you cut from the other end of the tube and removed from the heater core and and fasten it to the nub on water pump housing use new screw type stainless Steel clamps. You have to take this one apart to put it on. Stick a 3/4 coupler into the other end and route a long section of 3/4 hose under alternator to the heater core using SS clamps where needed. job done... Just leave the old tube where it is under the intake manifold......Thank you Very Much

Feb 14, 2012 | 1999 Lincoln Town Car

2 Answers

Where are all the freeze plug located on 4.6 w/auto. is there one between the block & transmission


Yes, there are expansion plugs (freeze plugs) on both sides of the engine block and at the rear of the engine block between the engine and transmission. There are also a couple in the ends of the cylinder heads.

With all that said, I would like to add that many times with that engine, the heater tube and connecting hoses can leak and be mistaken for a rear expansion plug leaking. I would definately check this before pulling the transmission out.

There is a tube that runs from the back of the water pump under the intake manifold and out the rear of the engine where it hooks up to the heater hose/heater core. This tube has a small hose connecting it to the back of the water pump. There is also a hole in the back of the engine block that will allow antifreeze from under the intake manifold to leak into the transmission bell housing area. When this tube or hose leaks, it often gets mistaken for a leaking rear expansion plug.

It is very easy to check for this. Remove the serpentine belt and remove the alternator and look under the intake manifold down in the "valley" between the cylinder heads. If there is antifreeze in there, the hose or the tube is leaking. Look at the picture below. Item #3 is the tube and hose assembly I am talking about. Usually, just the hose is leaking. It should be replaced with a short piece of SILICONE heater hose. On some of the vehicles, there are 2 hose clamps. On others, the end of the hose that is attached to the tube has a crimped collar on it. If yours is like this, you can fix it by carefully cutting the crimp collar off and replacing the hose using band clamps. (screw-type)

Also look for antifreeze leaking into this area from the front intake manifold runner. They tend to leak on the front runner near where the thermostat housing is located. These will also leak into the valley area and run out the back of the engine. If the manifold is leaking, chances are it is warped. DORMAN makes a replacement intake manifold kit just for this purpose because it has been so common. It is also very easy to check for this with the alternator removed.
The DORMAN part number for your vehicle is 615-178 (See second picture below)


dttech_203.gif

dttech_49.jpg

Sep 21, 2011 | 1996 Ford Mustang

1 Answer

I am seeing water behind the pump on the top of the motor in the v under all the fuel injection / intake is that normal for water pump to leak there if its bad?


its not normal. the water pump will leak in front, not back. There is a pipe and hose down in the VEE that can leak. If the pipe is bad, you will need to remove the pump to replace it. The intake manifold will need to come off, to replace the pipe/ hose. the hose connects a pipe behind the water pump to a pipe at the rear of the block to a heater hose.

Dec 12, 2010 | 2000 Ford Expedition

2 Answers

Engine races when idle


check hoses on engine for air leaks.

Feb 06, 2010 | 2003 Ford Expedition

2 Answers

I have a 98 lincoln town car executive and I need to know how you change the thermostat


1. drain coolant
2. remove engine cover
3. remove the 2 bolts from water hose connection (upper rad hose connecting to)
4. remove o-ring and thermostat
5. repeat in reverse order

Feb 05, 2010 | 1998 Lincoln Continental

3 Answers

93 lincoln town car coolant leak from rear of motor


Instead of removing the intake manifold and the the leaky manifold coolant hose, we simple place a 1" dia hose about 3" long with a **** down it so it can fit around the leaky coolant hose with two hose clamps and an agressive amount of "right stuff" silicone sealant and let stand for 24hrs which should fix the problem

Dec 26, 2008 | 1996 Lincoln Town Car

1 Answer

Water leaking fron back of engin


its a intake manifold or the heater core return hose to the rear of intake

Oct 21, 2008 | 1999 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...