Question about 2004 Dodge Ram 3500 Truck

Open Question

How to fix code 0633 on 2003 dodge 3500 diesel

How to fix and clear code 0633 on 2003 dodge 3500 diesel

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 29 Answers

SOURCE: Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel

I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Posted on May 03, 2009

BCally1
  • 133 Answers

SOURCE: serpentine belt diagram for a 5.9 diesel with air and 9 pulleys

5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :

  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Posted on Jan 22, 2009

  • 840 Answers

SOURCE: Need serpentine belt diagram for Dodge Ram 3500 diesel truck

no you should be able to do it There should be a routing label on the underside of hood or on the radiator support/ Its should not be very hard if you have one already just loosen the Alternator it will slide down get the other one ready look to see the way its routed then slide the new one and tighten up the alternator thats it/ Please rate my response thank you very much

Posted on Jan 31, 2009

  • 1348 Answers

SOURCE: serpentine belt diagram 2007 dodge 5.9 3500

get the belt routing from the local dealer.
they will not charge alot of money for a reprint from the factory service manual.
also
dayco belts come with the belt routing on the box.

Posted on May 28, 2009

badealer888
  • 414 Answers

SOURCE: 2005 Dodge 3500 Smoke (Blow-by)

first determine where the oil is coming from. Turbo seal leaks will cause oil to burn. Also check crankcase pressure regulator.
What signs are leading you to blow by?

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a wiring diagram for a 1997 Dodge RAM 3500 diesel pickup?


1997 3500 Wiring Diagram - Dodge Diesel - Diesel Truck Resource Forums

www.dieseltruckresource.com/...dodge-ram.../1997-3500-wiring-diagra...
Jan 24, 2011 - Hey guys, I'm working on a 97 3500 that's had the bed removed and replaced with a flatbed. There is the biggest mess under that truck wiring wise and. ... 2007 Ram 3500 A/C compressor wont engage, need wiring diagram ...

Dodge Wiring Diagrams / Schematics - YouTube

? 1:13
https://www.youtube.com/watch?v=UI6_vhCHFYU
Nov 19, 2013 - Uploaded by Robert Nauert
Dodge Wiring Diagrams / Schematics ... Nitro, Power Wagon, Ram 1500, Ram 2500, Ram 3500, Ram 4500 ...

1997 Dodge Cummins - Full color wiring diagrams - 12 Valve ...

forum.mopar1973man.com/.../1638-1997-dodge-cummins-full-color-wi...

Jan 01, 2016 | Dodge Cars & Trucks

1 Answer

I'm getting a F707B and F707A (APS Relay - Contall circuit open) error code on Dodge Ram diesel. Any idea what could this be? Truck runs great - just the AC on passanger side does not work as well as on...


sounds like a wire is disconnected somewhere, check for melted wires, or one that has a lot of grit or corrosion on it. Use a good electrical cleaner. Clear codes and retry your diagnostics test.

Sep 07, 2013 | 2005 Dodge Ram 3500

1 Answer

Cummins diesel in 2001 Dodge is cutting out and mild surge. code#s are P0500,P0370 P1693


you have codes related to the pcm, transfer pump and a vehicle speed sensor. these could be related or all individual issues. related issued could be wiring, untill you start doing testing it will be hard to tell.
start cheap and test the speed sensor first, then you can clear the codes and continue on any codes come back.


Disconnect the PCM harness connector(s).
Disconnect the Vehicle Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 5 Volt Supply circuit between the VSS harness
connector and the PCM harness connector.
Is the resistance above 5.0 ohms?

Jun 10, 2012 | 2001 Dodge Ram 3500 Truck

1 Answer

2001 dodge ram 2500 4x4 diesel code p0236


the code is map sensor too high, too long. certain programmers with boost foolers can cause this. if running a programmer disconnect and if problem isnt fixed replace the map sensor.

Apr 01, 2011 | 2001 Dodge Ram 3500 Truck

1 Answer

I HAVE A 07 RAM 3500 WITH A DIESEL IM GETTING TWO CODES POPN UP P2509 AND P2146 PLEASE HELP


Doesnt look like they go that high.....??

Here's a list of all the codes

http://www.allpar.com/fix/computer-codes.html

Jun 18, 2010 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

How do I clear the error codes on a 2001 Dodge Ram 3500 diesel?


You will need a hand-held obd2 scanner to clear the codes. Advanced Auto store will do it for free if you have one in your area. Other part stores will also do it for free.
You can disconnect the negative battery cable for 10 minutes and replace it, but it doesn't always work. Sometimes the codes are stored in memory and require the hand-held obd2 to clear them

Apr 19, 2010 | 2001 Dodge Ram 3500 Truck

1 Answer

Where is the turn signal fuse on a 2001 Dodge 3500 diesel truck? I changed the flasher and that didn't fix the problem of no turn signals or four way flashers.


This problem sounds like one I have faced several times on my 2001 diesel Dodge. The culprit has been a fuse under the hood in the fuse panel on the driver's side, up near the steering column. Look through the clear top of the fuses you see, chances are excellent that you will find a green one with the little electrode "popped". This is common when you plug a round trailer plug in upside down, or otherwise ground a powered circuit for the lights through the trailer plug. Simply pull and replace, I keep a couple spares in the glove box because of this problem. Also, if you use the truck to go to the auto parts store, keep in mind that you have no brake lights either. Hope this works for you.

Aug 11, 2009 | 2001 Dodge Ram 3500 Truck

1 Answer

Drive belt schematics


8366f3c.png
2004 Dodge 3500 w/5.7L Diesel

Apr 12, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

Dodge 3500 diesel trouble codes


the code is for low turbo boost which may have been caused by the snow.if you arent detecting any power problems try unhooking the batteries for about 10 min to clear the codes or take it to like and auto zone or advanced auto and have them clear the codes. if the light comes back on you may need to take it to the dealer because it may have a bad turbo ..a bad sensor ...or and air leak in the charge air system

Jan 03, 2009 | 2006 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...