Question about 2000 Nissan Frontier

1 Answer

I have a 1999 frontier that the code shows it needs a knock sensor or a crankshaft sensor. Is there anyway I can tell the sensor I need without buying both. Truck will not even start.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

The knock sensor won't make the truck not start. The crank sensor will make it not start.

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I bypass a knock sensor on a 2000 Nissan frontier


Bypassing (hotwiring) the knock sensor will remove a signal the computer needs to operate. Unexpected results for sure , possible damage to the computer may result. Replacing the knock sensor is the best way.

Oct 12, 2014 | 2000 Nissan Frontier

1 Answer

2000 nissan frontier rough idle and has a po325,po300,po120,and po304


THROTTLE POSITION SENSOR, MISFIRE, #4 MISFIRE, KNOCK SENSOR, THESE ARE YOUR TROUBLE CODES, PO120,PO300, PO304, PO325, RESPECTIVELY, REPLACE THE TPS @ THROTTLE BODY, REPLACE KNOCK SENSOR , @ ENGINE BLOCK, REPLACE YOUR SPARK PLUGS & PLUG WIRES ! AND YOU MUST ALSO REPLACE BOTH YOUR AIR & FUEL FILTERS, DISTRIBUTOR CAP & ROTOR , INSPECT, MAY NEED TO REPLACE, I WOULD ANYWAY !!!!!!!! ADD SOME GOOD FUEL INJECTOR CLEANER TO TANK, NEXT FUEL UP !

Apr 02, 2013 | Nissan Frontier Cars & Trucks

1 Answer

Engine misfire and knock sensor bank 1 codes on 1999 Nissan frontier 3.3 v6


I would want to see the actual codes, but if it is one or two cylinders you could have a failing injector and it not show up as a trouble code.
If one of the injectors is failing it can have a high resistance and affect the other injectors in that circuit.
The O2 sensors and cat would not affect a power loss in one or two cylinders, and the O2 sensor codes would be present.
The knock sensor only measures vibration, so it was probably ok before you replaced it.
There is a chance the cap is shorting out internally which would be tough to see, and the optic sensor in the bottom of the distributor could be causing problems too. Some of the cylinders may not be firing when you think they are.

Sep 21, 2012 | 1999 Nissan Frontier

1 Answer

I have a code p0325 knock sensor 1, circuit bank 1 or single sensor problem


A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block.

This P0325 code may show up intermittently or the Service Engine light may be lit constantly. Other knock sensor related DTC codes include P0330.

Symptoms: You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.

Causes: A code P0325 most likely means one or more of the following has happened:
* The knock sensor is faulty and needs to be replaced
* There is a wiring short/fault in the knock sensor circuit

Possible Solutions
* Check the resistance of the knock sensor (compare it to factory specs)
* Check for broken/frayed wires leading to the sensor
* Replace the knock sensor


Test it and tell us news.

Mar 15, 2011 | 1999 Nissan Maxima

2 Answers

Location of Crankshaft Position Sensor 2002


in the rear of the engine on the drivers side at the top of the transmission bell housing

Jul 08, 2010 | 2002 Nissan Frontier Crew Cab

1 Answer

2000 nissan frontier knock sensor code & distributor


no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Jun 14, 2010 | 2000 Nissan Frontier

1 Answer

1999 3.5L OLDS INTRIGUE,HAS ROD KNOCK,COLUD IT BE A BAD SENSOR OR A BAD HARMACA BALANCER?


any codes would show if sensor bad or going bad a rod knock is internal lower engine problem(connecting rod) rod knock can b bearing -rod-pin -piston harmonic balancer is on crankshaft out side of block if bad usually breaks off or causes heavy vibration

Nov 04, 2009 | 1999 Oldsmobile Intrigue

4 Answers

Where is a knock sensor for 1998 Mercury Villager located?


Here is a image of it's location, I hope it helps.
8262b2e.jpg

May 18, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
2000 Nissan Frontier Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...