Question about 1999 Pontiac Grand Am GT

1 Answer

My driver side window fell into the door & i can't get the door panel off...i have removed three screws (they were all i could find)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Pontiac Master
  • 752 Answers

The panel should pop off around the sides and make sure ur arm rest doesnt have a cap over it with hidden bolts there always a couple of hidden bolts

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear door panel removal:rear door window just fell down oneday and i was told it might just be off the track. it has electric windows


Its not off the track!!
You just lost the holders clipping your window glass piece.
  • Look for screws in door panel or around the speaker vents.
  • If you are sure that the speaker cant be removed without opening the door panel then read this below.
  • Mostly seen near areas like door lever(inside), power window switch set, bottom and each sides of the whole panel.
  • If its manual window, then look for a circle clip in between the winding window lever and the door panel. Plunge screw driver between them a make a gap then look.
  • Assure that all clips or screws which obstacles the removal of the panel.
  • Simply pull the panel from sides towards you

Sep 23, 2011 | 2007 Chevrolet Malibu SS Sedan New Cars

1 Answer

Glass fell 99 olds 2 door left side...regulator needs to be replaced in Riverside CA area


glass fell down in door bolt to equalizer arm to regulator fell out of place missing or window regulator broken.you have to remove door trim panel. you need a haynes repair manual to show you how to remove door trim panel. and door panel screws location to door handle.you need see screws location to remove power windows and door lock control.you will need door panel trim removal tool.

Jun 06, 2011 | 1999 Oldsmobile Alero

1 Answer

How to take door panel of? window fell off of track i beleieve


there will be 2-4 screws you will need to unscrew. usually one located around inner door handle and 2 of more around arm rest and maybe some on the lower part of the door and panel. the screws are usually covered by plastic covers. you can remove these with a small flathead screw driver to find the screws. after all screw have been removed carefully pry the panel off with plastic pry bar to prevent scratching. it will literally "pop" off with clips. be careful, you dont have to use tons of force, check to make sure all screws have been removed. then the panel will hang there because its still connected to lights, switch, and door handle. remove these connectors and the panel will come right off. if the window fell off the track, it might be as simple as screwing it back on the window regulator. worse case the regulator linkage is cracked and you will need a new window regulator.

May 04, 2011 | Cadillac DTS Cars & Trucks

1 Answer

NEED TO REMOVE DRIVERS DOOR PANEL ON A 2006 NISSAN 350Z


I did this myself before:

Removing the Door Panel

The first thing to do is remove the tab in your door handle that covers the screw (using the flat head screw driver), which secures the handle and window/lock switches to the door panel. Using the Phillips head screw driver, remove the screw. Now, remove the door handle and locate the tabs securing the wire harness for the door locks & power windows. Using the flat head, push down on the tabs and pull the male end out of the wire harness with your other hand. You can now locate 2 of the 3 bolts/screws that secure the door panel to the door.Using the 10mm socket, 3′ extension, and the 1/4′ drive socket wrench – remove the bolts/screws. Located behind the interior door handle is a plastic covering with a hole cut in it, that goes around the rubber piece that is there to stop the handle.Use the flat head screw driver to remove that plastic piece. Behind that piece, you will find the 3rd and final bolt/screw that secures the door panel. Using the 10mm socket, 3′ extension, and 1/4′ drive socket wrench, remove the bolt/screw. At this point you can pull the door panel off by hand.There are only tabs holding it on now, and they all will pop off. Now on the inside of the panel, you will need to locate the backside of the interior door handle. Remove the cables that operate the door lock, and opening mechanism. No tools are required for this step. Now you have the metal door panel, which is secured by 11-12 bolts/screws around the boarder of the panel.Locate the wire harness for the window motor in the upper right corner of the metal door panel. Using the flat head screw driver, disconnect the wire harness.After removing the panel, you will need to push the rubber grommet through the panel – the wire is attached to it. There will also be two white tabs on the backside of the panel that secure the female end of the window motor wire harness to the panel. Using your fingers (or pliers) pinch them, to remove the harness.

At this point, you can remove the 11 – 12 bolts/screws that are holding the panel to the door.The panel will not fully remove, but will come off a little bit. Now for the gold colored bolts/screws and nuts.Three of the bolts/screws are what secure the window motor to the panel.The other two bolts/screws, and the 2 nuts hold the brackets that hold the glass in place.there is one of these bolts/screws, and one of these nuts on each bracket (on each side). Using the 10mm socket, remove all of the bolts/screws.The Nuts are a 12mm socket; remove them as well. The panel should now come off, and the motor & guts of the door, will be revealed.


Apr 14, 2010 | 2005 Nissan 350Z

1 Answer

Driver side power window wont go up.Door was closed with an object at bottom and i heard a rattle like something went off track.What do i do.How do i remove inside panel?I have taken out all visable...


The window probably fell off track. You will have to remove all the screws and window and lock controls. Then take a large flat-head screw driver and gently pry off door panel. You will then have access to window and motor.

Sep 30, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Window came off track and fell into door need to get panel off and reconnect so window rolls up and down. this is on an 1984 chev s-10 drivers side window need advice on removal of door panel,and possible...


All you need to do first is remove the screws that hold the door handle on there should be three, next gently pop the panlr off useing a screw driver do not break the wires that control the windows and door locking system and then if you need to replace the entire window track do so but if you do not need to do not if you do it is easy to do so just remove the nuts at the botom of your door , they hold the window track in place and then remove the three bolts that hold the motor in place and then next gently pull the window up and then remove the traco after you have removed the window and reverse the process when putting new track in.

Sep 13, 2009 | 1984 Chevrolet S-10

1 Answer

A basketball goal fell on my wifes 2003 pontiac montana and it broke the mirror on drivers side. how do i get the mirror off?


You gotta pull door panel find screws for arm rest, pull door hand off, you have push type retainers around panel need to get door panel tool from parts store or carefull use & bent screw driver to pry & pop off from there unplug harness connectors to panel & remove panel pull plastic dorn in front of door you should have 3 10mm head nuts on mirror studs good luck

Sep 07, 2009 | 2003 Pontiac Montana

1 Answer

Driver door window fell inside door


lower window motor to middle, remove all door panel screws, once removed u will see a metal holder that will hold window, then u will see two or three holes for bolts , re install the bolts, if u dont see them check bottom of door area, there is a small section of door panel to manuever , but you can re install the bolts, check the window/door seal if it is hard spray with lubricant to prevent pressure against the motor.put door panel back , your back in business

Jul 27, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Window off track driver side 1997 sebring


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Mar 23, 2009 | 1997 Chrysler Sebring

1 Answer

HOW DO I REPLACE THE DRIVER SIDE POWER MIRROR ON AN 98 F-150?


Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

Jan 31, 2009 | 1997 Ford Expedition

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...