Question about 2006 Infiniti QX56

Open Question

What does it mean when the VDC off switch is on? And the 4lo light does not go off?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4LO has been blinking and check engine permanently on,on my Lexus 2013 570,what can I do


First have the codes read. 4LO cold be the switch, controller or the module. Engine light, Well anything to do with the drive train.

Aug 05, 2016 | Lexus Cars & Trucks

1 Answer

What does Brake light,VDC light and slip lights on . This happened when brake pedal pulsates,but I do have brake pedal.


See if the following information helpful:
1. Keep an eye on the dashboard for the indicators marked "SLIP" and "VDC Off" which will tell you the status of the computerized handling system if handling isn't normal. "SLIP" will blink when VDC is operating. "VDC OFF" means the system is off. Turn the VDC system back on if the Nissan's handling is poor by pressing the "VDC Off" button until the light goes out.

2. Adjust your driving if "SLIP" comes on. "SLIP" means the road conditions may be slippery. The VDC aids in steering and stopping, but be careful, even if VDC is engaged.

3. Remove any aftermarket suspension parts like enhanced shock absorbers if the "VDC Off" light comes on and handling is bad. The VDC system is geared for stock equipment and tires only. Use winter tires or snow chains on snow-covered roads. VDC won't substitute for the correct winter equipment.

4. Don't drive on very inclined corners with high banks and leave the VDC switch on if the handling is poor with VDC on. The system can't operate properly in that environment. Disengage VDC, or avoid those kinds of roads.

May 21, 2014 | 2004 Nissan Titan

1 Answer

2000 gmc 4x4 shifting problem


change your push button switch had same problem

Nov 24, 2011 | 2000 GMC Sierra

2 Answers

I have a 02 Chevy Z71 1500. I locked it in 4lo and now my (service 4wd) light is on and the lights on my panel for my auto, 2wd, 4hi and 4lo don't work. Plus it will not come out of 4lo. Any answer's?


Okay the motor for the 4x4 got stuck in 4LOW, Can you accsess the 4x4 motor switch,at see if that will retract the motor and default to 2 wheel drive because the switch itself went bad and wont disengage. see if that will help if not youll just have to by pass the switch and trigger to its normal position make sure its in neutral also

Apr 23, 2011 | 1999 Chevrolet K1500

1 Answer

4wd issues!!! When I start the truck, all 3 lights( 2hi 4hi and 4lo) flash once on the switch then go off ( all of them). It drives just fine but is in 2wd. When I push any of the buttons the 4hi and 4lo...


THE 4WD SWITCH IS A PROBLEM. ALSO THE GROUND CONNECTOR ON THE FRAME CLOSE TO THE DRIVERS DOOR IS A PROBLEM. IT USUALLY HAS A COATING OF THE UNDERCOAT MATERIAL ON THE FRAME THAT IS NOT REMOVED BEFORE THE CONNECTORS ARE PUT IN PLACE.

THERE ARE 2 BOLTS THERE THE OTHER IS AN ABS GROUND CLEAN OFF THE UNDERCOATING FIRST, PUT DIELECTRIC GREASE ON THE CONNECTION POINTS, THEN COVER THEM IN SPRAY ON UNDERCOATING. THIS IS A CHEAP FIX TRY IT FIRST.

RATE ME PLEASE.

Jul 24, 2009 | GMC K1500 Cars & Trucks

1 Answer

Chevrolet truck 4wd switch blinks


If they are blinking I believe it means that there are fault codes present in the pcm. You need to get the computer scaned to see if there are an codes present. If you live near an Autozone or Checker autoparts they can scan it for free.

Jun 21, 2009 | 1996 Chevrolet K1500

1 Answer

Service 4wd light


what causes the 4wd to kick in when you have it in 2wd

Mar 13, 2009 | 2004 GMC Yukon

1 Answer

Sometimes when i take off fast a slip light comes on does that mean my transmission is slipping?


I found your answer here:

Why Does the SLIP Light Come on?
The SLIP light represents the vehicle's traction control program. When illumiated it takes over control of throttle and braking based on input from a myriad of sensors. The VDC (traction control) is initiated by wheel slip, yaw and any other factors that make the computer think you're on the verge of loosing control of the vehicle. There have been a lot of complaints about the G35's VDC being too interferring and actually causing harder driving conditions. The VDC can be turned off via a switch to the lower left of the steering wheel (useful if trying to pull out of a snowy spot when wheel spin is necessary, or "spirited" accelerating). Even with the VDC turned off, however, it will still kick in if it detects substantial loss of control. NOTE: if you plan on racing, turn the VDC off. Otherwise it will ****** the throttle when you chirp the wheels from 1st to 2nd gear.

Dec 21, 2008 | Infiniti G35 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

722 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14204 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...