Question about 1992 Ford F350

1 Answer

How many bolts on a 1992 ford diesel 7.3 starter and how do you remove them

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 158 Answers

There are 3 bolts holding your starter on. i suggest a socket, long extension and a ratchet for the top hard to reach bolt. wrench works fine on the other 2 bolts

Posted on Feb 11, 2010

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 71 Answers

SOURCE: Starter Bolt

Obviously you do not have the one missing; therefore I would do one of two things... Take out one of the others, if there three, then no problem the other will hold till you get the other two back in. If the one you lost is broken off in the bell housing, then you must take off the starter and drill out the broken bolt and you can get a replacement from the Ford dealer, Pep Boys or a junk yard.


Good luck

Posted on Jan 02, 2009

  • 13 Answers

SOURCE: is there any bolts that

No, there are no bolts that hold it in from the back side, but make sure that you have removed the air conditioning compressor/power steering bracket so that it will clear the studed bolt on the water pump housing that the bracket rests on.

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to acces the 4 nuts on a ford transit starter motor as u tube suggest cuting a hole in the body of my van ,are there special tools to do it


which mark version /model /year transit van do you have

most starter motors for the ford transit diesel or petrol
show pictures as only two bolts to hold them on
between exhaust and motor/gearbox housing

Ford Transit Starter Motor Starter Motor For Sale New and Used

this one with three bolts may be a bit of a problem


FORD TRANSIT MK3 MK4 MK5 2.5 D Di TD 2.5 DIESEL NEW RMFD STARTER MOTOR 86-00


26387587-dgghzwtl0kutpuyxiasdr24z-2-0.jpg

Dec 06, 2016 | Ford Cars & Trucks

1 Answer

Removal of starter off a e350 cargo van 7.3 liter diesel year 2000


DISCONECT BATTERY STARTING WITH NEGATIVE
REMOVED WIRES AT STARTER
REMOVED BOLTS HOLDING STARTER TO ENGINE
REPLACE IN REVERSAL

Jul 08, 2011 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

How do you get to the starter to change it out on a 2004 f30 diesel?


park unit on level grond ,disconect batteries, choke weels, jack up passenger side and suppor on stands
there is 3 bolts holding the starter in place 2 points to the rear and one points to the front the top bolt pointing to the rear is trickier to get to removed starter from hole suport unit and removed small wires first
at starter selenoid then removed battery power wire assemble in reverse tacking care to index wires

Mar 06, 2011 | 2004 Ford F350

1 Answer

How do you remove and replace a starter for a 1992 2.6L Isuzu Amigo?


1.The battery negative and more importantly positive cable must be disconnected.
2. There are 2 14mm bolts holding the starter in place, the upper bolt can be removed by leaning over into the engine compartment from under the hood with a socket and extension on a ratchet or a ratcheting wrench.
3. crawl under the front passenger wheel and remove the positive cable nut, remove positive cable from starter.
4. unclip the small ground wire attached to starter.
5. remove the lower starter bolt.
6. There is room on the bottom of the vehicle to wiggle the starter down to the floor and out from under the vehicle. There isn't enough room to get the starter out from the engine compartment up and out from under the hood.
7. installation of new starter is reverse of installation.

This procedure should work on any Isuzu Rodeo, Trooper, Amigo, or Honda Passport with a 2.6L 4 cylinder 4ZE1 engine

Nov 12, 2010 | 1992 Isuzu Amigo

2 Answers

How do you replace the starter on a 1989 SW1500?


The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
  1. Disconnect the negative battery cable at the battery.
  2. Raise and support the vehicle.
  3. Disconnect and tag all wires at the solenoid terminal.
Reinstall all nuts as soon as they are removed, since the thread sizes are different.
  1. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.

f6823f2.gif
Starter mounts-5.7L and 7.4L engines

  1. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck.
To install:
  1. Position the starter and tighten all bolts as follows:
R/V Series:
  • Thru-bolts: 40 ft. lbs. (54 Nm)
  • Bracket bolt: 30 ft. lbs. (41 Nm)
  • Nut (gas): 11 ft. lbs. (15 Nm)
  • Nut (diesel): 90 inch lbs. (10 Nm)
C/K Series:
  • Thru-bolts: 35 ft. lbs. (45 Nm)
  • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
  • Nut (diesel): 75 inch lbs. (8.5 Nm)
  1. Reconnect all wires.450af3b.gif

Disconnect the negative battery cable


56132e9.gif
Remove the starter retaining bolts


d54e957.gif
Remove the starter from the vehicle

Apr 26, 2010 | 1989 Chevrolet Suburban

1 Answer

How to replace starter 5.4l


The starter is bolted to the bell housing.
Is has a positive cable from starter solenoid.

1. Remove the negative battery cable at the battery.
2. remove the power cable from the starter.
3. remove the starter mounting bolts (typically only 2 bolts)
4. Install new starter. Hand tighten mounting bolts
5. Secure both bolts to about 35 Lbs of torque
6. Connect power cable.
7. Connect the negative battery cable at the battery.
8. Test (start the car).

Oct 15, 2009 | 1999 Ford Expedition

2 Answers

How to get top bolt off of 1988 F250, 7.1 L diesel starter


You need a long extension and swivels for a rachet to get to the one bolt thats on top next to the block. Check for a way to get to it from the front.

Jun 25, 2009 | 1988 Ford F 250

1 Answer

1994 oilpan


Remove the starter, remove the flywheel dust shield, remove the motor mounts center bolt, jack the engine as far up as possiable, this will then give you access to the oil pan bolts.

Oct 14, 2008 | 1994 Ford F350 Crew Cab

1 Answer

1992 f350 7.3 diesel


as much as i would like to tell you there is but if its broke there isnt if the bolts holes were stripped out that could be fixed. that engine turns over very hard.
dont feel bad your not the first one with this problem
later
paul

Sep 17, 2008 | 1992 Ford F350

Not finding what you are looking for?
1992 Ford F350 Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...