Question about 1979 Pontiac Firebird

1 Answer

I'm looking for the pulley infomation for my 1970 pontiac 400 - I would like to know if a mid 70's power steering and alternater pulley assembly should line up with original cranck pulley.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 2,002 Answers

If my memory serves me right, both belts run off the main crank pulley and over the fan pulley. The power steering should line up on the pulley closest to the block and the alternator would be the next one out from that. Hope this helps.

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering fluid leaking on 2002 pontiac grand prix


OK you know the problem but is it something as simple as replacing the Power steering hose or as complicated as also needing a new power steering pump also? Look at where its leaking to determine what needs replacing. Remember it just takes a little time to determine where its leaking. If you find that its not the hose leaking but its the power steering pump then follow these easy steps and save $100s doing it yourself:
1 Remove the negative battery cable with a wrench and place it aside. Remove the upper strut housing tie bar if necessary for access. Remove the power steering serpentine drive belt and electrical plug on the TFE off as applicable. Remove the lower bolt from the mounting bracket using a socket and ratchet if necessary for access. Take off the inlet and outlet hoses from the power steering pump. Remove the reservoir hose only on the supercharged engine. You will need a flat-head screwdriver for this task.
2 Place the power steering pump pulley so the bolts can be accessed through the hole in it. Remove the mounting bolts, using a socket and ratchet, through the hole in the pulley. Take the power-steering assembly out from the bracket. If necessary transfer the pulley to the new pump with a pulley puller.
3 Replace the power steering pulley assembly before you install the pump using the pulley-install tool from your kit. Start the power steering inlet hose connection to the pump by hand. Replace the power steering pump assembly to the engine. Replace the lower bolt first, making sure the hose and heater pipe have enough clearance so they do not touch. If the two rub together they will make noise after the installation is finished. Replace the outlet hose to the pump, directing the hose under the engine harness and the heater hose. If the engine is supercharged it will be necessary to connect the hose from the reservoir.
4 Torque the power steering gear inlet hose to 20 foot-pounds and the hose clamp at the pump to 15 inch-pounds. Torque the pump mounting bolts to 20 foot-pounds. If equipped with a TFE pump, attach the connection. Replace the power steering drive belt or serpentine belt if you removed either. Replace the upper strut tie bar and torque the nuts to 18 foot-pounds. Replace the negative battery cable and fill the power steering reservoir with fluid. Bleed the steering system by starting the engine and turning the steering wheel right and left until all the air is out.

Apr 20, 2014 | 2002 Pontiac Grand Prix

2 Answers

Trying to replace water pump can get to last bolt at power steering pump pulley interference 2004 pontiac gran prix gt 3.8


Check this procedure for Pontiac 3.8L Engine - Water Pump
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:
    Negative battery cable. Drive belt Water pump pulley Power steering pump and move it aside Water pump

    zjlimited_668.gif

    Fig. Exploded view of the water pump assembly mounting-3.8L engine

To install:
  1. Install or connect the following:
    Water pump using a new gasket and torque the long bolts to 25 ft. lbs. (34 Nm) and the short bolts to 16 ft. lbs. (22 Nm) Water pump pulley and torque the bolts to 115 inch lbs. (13 Nm) Power steering pump and torque the bolts to 25 ft. lbs. (34 Nm) Drive belt Negative battery cable
  2. Fill the cooling system.
  3. Start the vehicle and check for leaks, repair if necessary.
Hope helps.

Sep 02, 2011 | 2004 Pontiac Grand Prix

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

How do i remove power steering pump on 02 grand am?


Remove the serpentine belt (loosen off the tensioner below the alternator). Remove the 3 bolts accessible thru the holes in the power steering pump pulley (13mm bolts). Remove the pressure hose bracket, at the rear of the alternator(15mm nut). Remove the pressure hose 5/8" nut, and electrical connector if it has one. Disconnect the return hose clamp, and lift out pump. It can be wiggled out from between the intake manifold and fuel rail. You may need a special puller tool to transfer the power steering pump pulley, if you are just replacing the pump assembly (there is also a tool to install pulley). If you are replacing the pump with pulley just reverse procedure.

Feb 23, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

Pulley removal


Youll need to use a power steering puller tool,U can get a loaner tool from advance auto to remove and install your pulley.It pressed it off and back on.

Feb 03, 2010 | 1966 Ford Mustang

2 Answers

How to replace power steering pump


2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg

Sep 07, 2009 | 2004 Pontiac Grand Prix

1 Answer

Does the 2005 pontiac grand prix have a variable steering unit?


The safest way to tell is by taking the VIN to the dealership parts department and asking them. If you know what to look for, there should be an electrical modulator valve on the PS pump or pressure line if it has variable steering.

Mar 14, 2009 | 2005 Pontiac Grand Prix

2 Answers

The power steering pump bolts all seem to have vibrated out, the unit came free and i can just move it around, the pulley moves freely, everything else seems to work ok


I don't have chrysler producs. I'll post 3.8L V6 Ford Windstar for reference. You'll get some idea.



Removal
ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.
  1. Using a 15mm socket or wrench on bolt attaching drive belt tensioner pulley. Rotate drive belt tensioner (6B209) clockwise to remove drive belt from pulleys.

    3.8L Engine

    e973ba6.gif
Item Part Number Description 1 10300 Generator 2 3A674 Power Steering Pump 3 19703 A/C Compressor 4 6B217 Drive Belt Tensioner Pulley 5 6312 Crankshaft Pulley 6 8501 Water Pump 7 6B209 Drive Belt Tensioner 8 8620 Drive Belt
Installation
  1. Install drive belt over all pulleys (except drive belt tensioner ).
  1. Rotate drive belt tensioner as described under Removal and install drive belt over drive belt tensioner pulley. Ensure that all V-grooves make proper contact with pulleys
---------------------------------------------------------------
Another example
Pulley, Power Steering Pump CII
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Drain as much fluid as possible from the power steering pump (3A674) through the power steering oil reservoir (3A697) neck.
  1. Install Steering Pump Pulley Remover T69L-10300-B on the power steering pump pulley (3A733) , and place the tool and power steering pump in a vise by gripping the small hex-head of the tool.
  1. Hold the power steering pump , and rotate the tool nut counterclockwise to remove the power steering pump pulley . Do not apply in and out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.

Installation
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal thrust areas.
  1. Place the power steering pump pulley on the power steering pump shaft, and install Steering Pump Pulley Replacer T65P-3A733-C. The small diameter threads on the tool should be fully engaged in the power steering pump shaft.
  1. Hold the power steering pump , and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. The power steering pump pulley face must be flush within 0.25mm (0.010 inch) of the end of the power steering pump shaft.
  1. Remove the tool.
  1. Fill the power steering oil reservoir to the COLD FILL line.
------------------------------------------------------------------------------------------
Steering Pump, Power Removal
  1. Disconnect battery ground cable (14301) .
  1. Remove accessory drive belt (8620) .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove right front wheel (1007) and tire assembly.
  1. Remove power steering pump pulley (3A733) .
  1. Position drain pan. Remove power steering pressure hose (3A719) and power steering return hose (3A713) from power steering pump (3A674) .
  1. Remove four power steering pump retaining bolts (three in front, one in rear) and remove power steering pump .
Installation
  1. Position power steering pump and install retaining bolts. Tighten retaining bolts to 41-54 Nm (30-40 lb-ft).
  1. Install power steering pressure hose and power steering return hose to power steering pump . Remove drain pan.
  1. Press on power steering pump pulley as outlined in this section.
  1. Install right front wheel and tire assembly. Tighten lug nuts (1012) to 115-142 Nm (85-105 lb-ft).
  1. Lower vehicle.
  1. Install drive belt to power steering pump pulley .
  1. Connect battery ground cable .
  1. Fill power steering oil reservoir (3A697) to proper level. Refer to Section 11-00 .

    Power Steering Pump and Bracket, 3.8L

    17c7689.gif
Item Part Number Description 1 N607528-S2 Screw, M6-1 x 16 2 8509 Water Pump Pulley 3 W804804-S2 Screw, M8-1.25 x 35 4 N806214-S2 Bolt, M12 5 W606691-S36B Screw, M8-1.25 x 35 6 10B315 Generator Brace 7 N621939-S36B Nut, M8-1.0 8 10300 Generator 9 6B212 Accessory Drive Belt Tensioner Bracket 10 6049 Cylinder Head 11 19D624 Air Conditioning Compressor Bracket 12 W606563-S2 Bolt, M10-1.5 x 55 13 19703 A/C Compressor 14 N807273-S100 Bolt, M8-1.25 x 121.5 15 3C510 Power Steering Hose Bracket 16 3A674 Power Steering Pump 17 3C511 Power Steering Pump Support 18 W807239-S8 Bolt, M10-1.5 x 36.5 19 2888 A/C Compressor Brace 20 W806342-S2 Bolt, M8-1.25 x 23 21 W606571-S411 Bolt, M10-1.5 x 113.5 22 6C348 Idler Assembly 23 3A733 Power Steering Pump Pulley 24 N805137-S56 Bolt, M10-1.5 x 157 25 N621939-S2 Nut, M8-10 26 N807241-S36B Bolt, M10-1.5 x 132 27 6B209 Drive Belt Tensioner A — Tighten to 8-11 Nm (71-101 Lb-In) B — Tighten to 20-25 Nm (15-18 Lb-Ft) C — Tighten to 70-95 Nm (52-70 Lb-Ft) D — Tighten to 40-55 Nm (30-40 Lb-Ft) E — Press Flush with End of Power Steering Pump Shaft

Mar 03, 2009 | 1994 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...