Question about 2001 Lexus LS 430

1 Answer

How to replace lexus 2001 ls430 middle tail lamp - harness does not come out after rotating it like bottom bulb harness

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 14,036 Answers

CAREFULLY TRY TO TWIST BULB HOLDER COUNTERCLOCK WISE TO REMOVE IT.

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing backup bulbs on 2005 buick rendevous


TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

Apr 16, 2017 | Buick Cars & Trucks

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

1 Answer

Tail lights on '01 lexus 430 wont come on


Check fuses first for rear park lamps. I do believe there will be 2 fuses for RR & LR tail lamps. Owners manual will state the location of the fuse junction box. If both fuses are good, I would next check to see if the park/brake lamp bulbs are good and are the correct type. If the bulbs are correct and okay, the turn signal stalk assembly has failed and needs to be replaced. BEFORE YOU REPLACE THAT PART............. If you have a trailer hitch installed, check the trailer hitch wire harness and make sure that it is not shorting out on anything metal due to poor installation. If that is the case, repair short and replace rear park lamp fuse(s). Hope this helps you out.

Sep 21, 2013 | 2001 Lexus LS 430

1 Answer

2001 jaguar s type - Right tail lamp failure message.... I replaced bulbs and fuse and tail lights still don't work but the dual element right break light does illuminate when I press the break also right...


There is a harness that you unplugged for the rear tail lamp. Make sure it is fully pressed and locked. This is always the cause on jags for tail lamp failure.

Dec 14, 2010 | 2001 Jaguar S-Type

1 Answer

How to change break lights


Tail Lights
  1. Open the endgate or liftgate.

  2. Remove the screws that retain the tail lamp assembly to the vehicle.
    32085_blaz_g0151.gif

    Tail lamp assembly removal

  3. Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.

  4. Remove the bulbs from the sockets.

To install:

  1. Install the bulbs into the sockets.

  2. Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.

  3. Install the tail lamp assembly to the vehicle.

  4. Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).

Oct 23, 2010 | 2000 Oldsmobile Bravada

1 Answer

REPLACE HEADLAMP BULB 2001 LEXUS LS430


There is a clip that pries up with small flathead screwdriver. The harness and bulb are held in lens with a plastic ring that screws on and off.

Sep 15, 2009 | 2001 Lexus LS 430

1 Answer

How do you replace a brake light?


serjoijr: To replace the bulb, you must remove the tail lamp housing.
Open the tailgate. There are two screws which retain the lamp housing to the body. You can see them when you open the tail gate, One is near the top and one is near the bottom. They are a phillips head type screw.
Remove both screws and pull the lamp housing directly backwards. DO NOT TWIST IT TO THE SIDE! The housing has a pin on the opposite side which interlocks with the body, keeping it in place on that side.
Once you have pulled the housing away from the body, you will see the lamp sockets and wiring harness. These sockets usually rotate to one side or another to interlock with the housing. Once the socket is removed, you can replace the bulb and return the housing back to the original spot.

Jul 28, 2009 | 2004 Honda Odyssey

3 Answers

How to locate the oxygen sensor in a LEXUS LS430 (Bank1 Sensor1)


the O2 sensor for bank one sensor one is located between the catalytic converter and the engine in the exhaust head pipe. see photo of your engine cylinder layout, the sensor u want to replace is the one at the cylinder #1 0aa2e73.gif bank on right.

Apr 15, 2009 | 2001 Lexus LS 430

1 Answer

How do i get the cover off the license plate bulbs?


REMOVAL PROCEDURE
  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.
INSTALLATION PROCEDURE
  1. Install the license plate bulb into the lamp housing.
  2. While supporting the tail/back up lamp assembly, install the tail/back up lamp harness grommet to the rear compartment lid and install the tail/back up lamp. NOTE: Refer to Fastener Notice in Service Precautions.
  3. Install the tail/back up lamp fasteners to the tail/back up lamp studs. Tighten Tighten the tail/back up lamp fasteners to 6 N.m (53 lb in) .
  4. Connect the tail/back up lamp electrical connector.
  5. Connect the tail/back up lamp harness connector and clip the connector to the metal edge of the rear compartment lid.

Feb 25, 2009 | 2000 Buick LeSabre

1 Answer

How do you replace headlight on lexus ls430?


This is one of the easiest fixes you can do on your lexus...all thats needed is just unscrew the canisters' holding the lightbulbs, they look like dome fixtures encasing the HID lights...once you unscrew those, the bulbs are held in place by simple snap components that actually hold the lights in place...pull the old lamps out...unplug them, and then reverse this procedure....it took me all of 15 minutes, and a savings of $1000 to do this...

Nov 21, 2008 | 2001 Lexus LS 430

Not finding what you are looking for?
2001 Lexus LS 430 Logo

Related Topics:

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...