Question about 2000 Mercedes-Benz M-Class

Open Question

How do you unlock an ml320 radio? just bought it but battery was disconnected working on airbag sensor. I guessed at 11111 but now it just says WAIT

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 64 Answers

SOURCE: I have entered incorrect radio code for my 01'

leave the radio on for a few days, with the wait displaying, it will display CODE after a few days, 2 - 3 days, then enter the correct code , everytime u enter a wrong code the time increases.

Posted on Mar 02, 2009

Ad
merctechniqu
  • 229 Answers

SOURCE: I have done all that

you must wait at least 3 ours for rest it. can't do any thing if you put wrong code must be patient for next turn, is this information helped you?

Posted on Oct 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the antennea?


no symptoms posted so i cant wax smart,

radio?

the whole thing or just unplug it from radio.

i have 06 FSM



satellite? radio or a/m F/m normal.



normal rad (FSM quoted)

WARNING: Disable the airbag system before attempting any steering wheel, steering column, seat belt tensioner,

side airbag, or instrument panel component diagnosis or service. Disconnect and isolate the battery

negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing

further diagnosis or service.

This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury. (or death)

1. Disconnect and isolate the battery negative cable.

2. Remove the headliner as necessary to access

antenna module.

3. Disconnect the electrical harness connector from

the antenna module.

4. Disconnect the antenna module connector from the

integral antenna.

5. Remove the mounting fasteners from the antenna

module.

6. Disconnect the coax lead from the antenna

module.

end quote.

Mar 10, 2015 | 2006 Jeep Liberty

1 Answer

How do i deactivate srs so i can replace front seatbelts on 2005 yaris


Disconnect the battery negative terminal.
1. Wait at least 90 seconds after the ignition switch is
turned off and the negative (-) terminal cable is
disconnected from the battery before starting the
operation.
(The SRS is equipped with a back-up power source, so
if work is started within 90 seconds of disconnecting
the negative (-) terminal cable of the battery, the SRS
may be deployed).
2. Do not directly expose the steering pad, front
passenger airbag assembly, center airbag sensor
assembly, front airbag sensor, front seat inner belt
assembly, seat position sensor, occupant
classification ECU, front seat side airbag assembly,
side airbag sensor, curtain shield airbag assembly,
rear airbag sensor or front seat outer belt assembly to
hot air or flames.

Feb 26, 2013 | 2005 Toyota Yaris 1.3

1 Answer

I have a '93 jeep cherokee and my horn doesn't work. I've checked the fuse and it's fine but now i don't know where to locate the horn itself to check for disconnections or to replace...


LOOK UNDER THE LOWER AIR DEFLECTOR FROM BELOW THE RADIATOR. IF YOU HOT WIRE CAR HORN AND IT WORKS.YOU HAVE TO REPLACE THE WHOLE AIRBAG IN STEERING WITH HORN CONTROL BUTTONS.YOU NEED TO DISABLE AIRBAG IN STEERING WHEEL WHEN REPLACING AIRBAG AND HORN CONTROL BUTTON PAD.JUST TURN OFF RADIO FIRST, THEN DISCONNECT REMOVE THE NEGATIVE BATTERY CABLE.WAIT 20 MINUTES BEFORE WORKING ON AIRBAG AND HORN PAD IN THE STEERING WHEEL.

Aug 12, 2011 | Jeep Cherokee Cars & Trucks

3 Answers

I have a dodge caravan 2000, and the horn doesn't work. I changed the relay fuse and fuses. It still doesn't work. Please help.


REMOVE HOTWIRE HORN OR PRESS REMOTE BUTTON LOCK CAR DOORS IF YOU HEAR CAR HORN BLOWS WHEN ACTIVATE CAR ALARM. HORN WORKING.MORE LIKELY THE AIRBAG AND HORN PAD NEED REPLACING.IF YOU GOING TO FIX. DISABLE AIRBAG IN THE STEERING WHEEL BEFORE REPLACING THE AIRBAG AND HORN PAD. TURN OFF RADIO.THEN DISCONNECT NEGATIVE BATTERY CABLE FOR 20 MINUTES BEFORE REMOVING AIRBAG IN STEERING WHEEL.THAT HORN PAD WITH AIRBAG IS NOT GOING TO BE CHEAP.

Jun 12, 2011 | Dodge Caravan Cars & Trucks

1 Answer

Would like to change on / off switch button in steering wheel for the cruise control on a 2005 impala, how do I remove the steering wheel airbag?


YOU NEED TO DISABLE AIR BAGS.FIRST. TURN OFF RADIO THEN DISCONNECT NEGATIVE BATTERY CABLE.WAIT 20 MINUTES FOR AIRBAGS DISCHARGE.THEN REMOVE AIRBAG IN THE STEERING BY REMOVING SCREWS BEHIND AIRBAG IN STEERING WHEEL.

May 25, 2011 | 2005 Chevrolet Impala

1 Answer

2007 toyota tacoma truck- 4 cyl. Dog threw up into air vent- how do I clean out the vent on passenger side?


DISARM AIRBAGS FIRST TURN OFF RADIO.DISARM AIRBAGS DISCONNECTING NEGATIVE BATTERY CABLE WAIT 10 MINUTES BEFORE WORKING ON DASH AREA.TRY REMOVING THE GLOVE BOX.SEE CAN YOU REACH AND REMOVE VENT DUCT WHERE VOMIT IS REMOVE VENT FROM DASH AREA.LOOK INSIDE VENT OR AROUND OUTSIDE VENT DUCT FOR NUTS HOLDING IT IN PLACE.IF YOU HAVE ANY TROUBLE REMOVING DUCT LET GARAGE DO IT.IF ALL GOOD WHEN RECONNECTING NEGATIVE BATTERY REARMING AIRBAGS WAIT 2 MINUTES BEFORE STARTING VECHICLE LET AIRBAGS LIGHT TURN OFF FIRST THEN ITS ARMED AND READY.

Oct 07, 2010 | 2007 Toyota Tacoma

1 Answer

BOUGHT NEW SEATS TO REPLACE BURNHOLE SEATS CAN I JUST DISCONNECT BATTERY THEN REPLACE THEN RECONNECT BATTERY? ALL OKJ AFTER THAT OPR NOT?


seats has nothing to do with airbag. replace the seat and make sure all wires if there are any, are reconnected, and sure the seat belt sensor are not touched. and the seat sensor are conncted back.

Jun 01, 2009 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

My airbags blew i need to replace them


You need to replace your "airbag diagnostic monitor", and the "airbag sensors" as well as the airbags.

Once your airbags have been deployed, the airbag sensors may be damaged and may cause deployment for no appearant reason. You must replace the airbag diagnostic monitor, because it's internal thermal fuse blows upon deployment, and will not deploy a new airbag.

If you purchase airbags, and related parts from a salvage yard, make sure the diagnostic monitor is the same model as the one in your vehicle (the model number is on top of the unit, the manufacturing date is listed last and is irrellevant), but ford does use the same unit in most vehicles of the same year.

To replace the system, disconnect your negative battery cable and wait 1 minute before doing anything. Your airbag system is designed to be able to deploy for 1 minute after a power failure, so do wait 1 minute before doing anything.

In a 1995, your airbag diagnostic monitor is located inside the vehicle, center console area, under the heater and blower control assembly. It is a silver box that has 2 wire clips connected to it, and is retained with a couple 10mm bolts. (Don't get it confused with the larger computer that is under the radio area, the monitor is behind the computer)

Your 2 sensors are located in the front of the grill area, and 1 is in the driver wheel well area. All are held in by a few bolts, and have a long wire clip attached.

The driver airbag is held in by 2 bolts that are easily accessed on the back of the steering wheel, then a couple wire clips inside the steering wheel.

The passenger airbag is held in by 4 bolts that are accessed, by removing the glove compartment, and a wire clip behind the airbag in the dash area.

Airbags blow with extreme power and can be as dangerous as helpful. If you intend on doing the work yourself, follow the instructions carefully.

Install everything in reverse, and DO NOT HOOK UP THE BATTERY UNTIL THE REPAIR IS FULLY COMPLETED!

I hope this helps you, and I wish you luck on your repair.

May 11, 2009 | 1995 Ford Thunderbird

3 Answers

Resetting Radio with WAIT on an 01' Ml 320


I've entered incorrect radio code and it is now stuck on WAIT. but i don`t have the code what can i do. pl. help me

Mar 01, 2009 | 2007 Mercedes-Benz ML320 CDI

Not finding what you are looking for?
2000 Mercedes-Benz M-Class Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...