Question about 1996 Chevrolet S-10 Pickup

1 Answer

I need to replace heater core & blower motor, need help removing dash.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 752 Answers

Everthing your looking for is on passenger side dash underneath blower heater core just remove bottom of cover and see if you can get to it..

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get to the blower motor for a 1995 dodge Dakota to replace it ?


Bad design on the 1995 Dodge Dakota. The dash has to be removed to replace the blower motor. May want to replace the heater core while the dash is out to keep from having to remove it later for a leaking heater core.

Feb 17, 2015 | Dodge Cars & Trucks

1 Answer

How hard is it to replace a front ac blower motor on a 2009 ford flex


You just have to be careful with the trim panels that Need removed. First remove right sill plate trim ( bottom of door opening ). Then remove lower a-trim. Remove two lower dash panel pin-type retainers and the lower dash panel insulator. The blower should be visible now. Remove blower motor electrical connector. Depress two retaining tabs on the vent tube between heater core housing and blower. Be careful tithe tube is only available as part of the hole heater core box. Turn the blower counterclockwise to remove from box

Jan 26, 2015 | Ford Cars & Trucks

1 Answer

I have a 1988 735i and smoke came out the inside vents recently.....fan barely works. Any suggestions??


If it smells sweet -it is coolant

If it just was brief & white is was refrigerant

If the blower works it is not a fuse

The blower motor may be old & worn out & need
replacing & you may have a leaking heater core

Good Luck under the dash

Look at some You Tube Video on R&R of
a heater core

Nov 06, 2014 | Cars & Trucks

1 Answer

I need an advice on how to replace the heater coil on my 1990 honda accord


( heater core) disconnect the cable from negative battery terminal, from engine compartment disconnect the temperature control cable from the temperature blend door and the mounting bracket from the top of the heater case. Disconnect wires from blower motor resistor and the blower motor. Drain the coolant from the radiator into some type of container. Disconnect the heater hoses from the heater core tubes on the engine side of the firewall. Now working in the passenger compartment, remove the nuts retaining the left end of the heater case and the right end of the plenum to the dash panel. Working in the engine compartment, remove the screw retaining the top center of the heater case to the dash panel. Remove the screws retaining the right end of the heater case to the dash panel and remove the heater case assembly from the car. Remove the screws, nuts and bolts retaining the heater housing plate to the heater case, then remove the heater housing plate. If so equipped, remove the screws attaching the heater core frame to the heater case and remove the frame. Remove the heater core and seal from the heater case.

Dec 25, 2011 | Cars & Trucks

1 Answer

Hi, i need to remove and replace the blower motor for the a.c./ heater, and dont know where it is located. can you please help?


Blower Motor Removal & Installation To Remove:
  1. Remove the insulator from under the right side of the dash.
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor retaining screws.
  4. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting screws.
  3. Connect the electrical connector to the blower motor.
  4. Install the under dash insulator.
prev.gif next.gif

Dec 10, 2010 | 1999 Pontiac Grand Prix

1 Answer

Is the heater core on a 1981 bronco in the engine compartment or the cab compartment


in the cab, but procedures are different depending on whether or not you have A/C. See below

1980-81 Comfort Vent Heaters, Without Air Conditioning
  1. Disconnect the heater hoses from the heater core tubes and plug the hoses with suitable 5 / 8 inch; (16mm) plugs.
  2. Remove the glove compartment liner.
  3. Remove two (2) spring clips attaching the heater core cover to the plenum along the top edge of the heater core cover.
  4. Remove eight (8) screws attaching the heater core cover to the plenum and remove the cover.
  5. Remove the heater core from the plenum taking care not to spill coolant from the core.
To install:
  1. Install the heater core in the plenum.
  2. Install the heater core cover (eight (8) screws and two (2) spring clips along the top edge of the cover).
  3. Install the glove compartment liner.
  4. Connect the heater hoses to the heater core. Tighten the hose clamps.
  5. Add coolant to raise the coolant level to specification.
  6. Check the system for proper operation and for coolant leaks.

1980-81 Standard & High Output Heaters, Without Air Conditioning
  1. Disconnect the temperature cable from the temperature blend door and the mounting bracket on top of the heater case.
  2. Disconnect the wires from the blower motor resistor and the blower motor.
  3. Disconnect the heater hoses from the heater core and plug the hoses with suitable 5 / 8 inch; (16mm) plugs.
  4. Working under the instrument panel, remove two (2) nuts retaining the left end of the heater case and the right end of the plenum to the dash panel.
  5. In the engine compartment, remove one (1) screw attaching the top center of the heater case to the dash panel.
  6. Remove two (2) screws attaching the right end of the heater case to the dash panel, and remove the heater case from the vehicle.
  7. Remove nine (9) screws and one (1) bolt and nut attaching the heater housing plate to the heater case, and remove the heater housing plate.
  8. Remove three (3) screws attaching the heater core frame to the heater case and remove the frame.
  9. Remove the heater core and seal from the heater case.

To install:
  1. Position the heater core and seal in the heater case.
  2. Install the heater core frame (3 screws).
  3. Position the heater housing plate on the heater case and install the nine (9) screws and one (1) bolt and nut.
  4. Position the heater case to the dash panel and install the three (3) attaching screws.
  5. Working in the passenger compartment, install two (2) nuts to retain the heater case and plenum right end to the dash panel.
  6. Connect the heater hoses to the heater core. Tighten the hose clamps.
  7. Connect the wires to the blower motor resistor assembly.
  8. Connect the blower motor wires.
  9. Position (slide) the self-adjusting clip on the temperature cable to a position approximately one 1 inch; (25.4mm) from the cable end loop.
  10. Snap the temperature cable on the cable mounting bracket of the heater case. Then, position the self-adjusting clip on the door crank arm.
  11. Adjust the temperature cable.
  12. Check the system for proper operation.

Oct 05, 2010 | 1981 Ford Bronco

6 Answers

1998 Ford Contour. The heater blower stopped suddenly. I checked all the fuses, good. I removed the blower and hooked it to 12 volts. Whoosh! It almost spun out of my hand. I checked the plug into the...


I dont know what these other guys are saying..I think they snif the glue!!! YOUR BLOWER FAN ASSEMBLY CAN EASILY BE REMOVED !!
1. Remove the wire
2.Find the "tab on the housing and pull it down while rotating the fan housing counter clockwise. This will remove the fan assembly. Plage 12 volts on the contacts to test the motor. If it works then the resister pack is blown. On the fan housing (near firewall ) you will see a plug going into a square looking box with a screw in it. Remove the wire then remove the screw to remove the resistor pack.. A new resistor pack is around 20 dollars at a ford dealer. Hope thie "FREE" info helps!

Feb 24, 2010 | 1998 Ford Contour

1 Answer

I need to replace the heater core & blower motor on a 1996 Chevy S-10. I need info on removing the dash.


i could send you directions with images to replace heater core need email address and 8th digit of vin, W or X

Feb 07, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

I need to replace my heater core on my 1995 Ford Ranger


Removal & Installation
4274678.gif
Exploded view of the blower motor housing and the heater air plenum assemblies

  1. Disconnect the negative battery cable. Allow the engine to cool down. Drain the cooling system to a level below the heater core fittings on the firewall.
  2. Disconnect the heater hoses from the heater core tubes and plug hoses.
  3. Remove the five nuts that secure the blower motor housing to the firewall.
  4. Pull the housing away from the firewall. Disconnect any wire harness plugs which inhibit the housing.
  5. Remove the remaining nuts which secure the heater air plenum (inside the passenger compartment) to the firewall.
  6. In the passenger compartment, remove the instrument panel. Refer to Section 10.
  7. Pull the heater air plenum rearward from the firewall and remove it from the vehicle.
  8. Remove the heater core from the heater air plenum.
  9. Inspect all air seals on the components and firewall and replace any that are damaged.

  1. To install:
  2. Install the heater core into the air plenum chamber.
  3. Position the heater air plenum against the firewall from the passenger compartment.
  4. Under the hood, install the plenum retaining nuts.
  5. Install the blower motor housing to the firewall and install the attaching nuts.
  6. Connect the heater hoses to the heater core tubes at the dash panel in the engine compartment. Do not over-tighten the hose clamps.
  7. Install the instrument panel.
  8. Check the coolant level and add coolant as required. Connect the negative battery cable.
  9. Start the engine and check the system for coolant leaks.

Oct 18, 2009 | 1995 Ford Ranger Supercab

1 Answer

How to replace heater core in a 1988 jeep cherokee?


Jeep Cherokee XJ Heater Core

Work for '92 models, but can use it like a reference guide.

6042054.gif

Figure 1

  1. Disconnect battery ground cable, then drain cooling system.
  2. Disconnect hoses from heater core.
  3. If equipped with A/C, remove evaporator/blower housing as follows:
    1. Discharge A/C system, then disconnect hoses from expansion valve.
    2. Disconnect electrical connector and vent tube from blower motor.
    3. Remove console, if equipped.
    4. Remove lower instrument panel attaching screws, then the lower panel.
    5. Disconnect electrical connections from A/C relay, blower motor resistors and A/C thermostat.
    6. Disconnect vacuum hose from vacuum motor.
    7. Cut evaporator/blower housing to heater core housing retaining strap, then disconnect heater control cable.
    8. Pry retaining clip from rear of blower housing flange, then remove the three retaining screws.
    9. Working from engine compartment, remove evaporator/blower housing attaching nuts, then the evaporator drain tube, Figure 1.
    10. Remove right kick panel, then the instrument panel support bolt.
    11. Pull right side of dash outward, then rotate housing downward and towards rear of vehicle until studs clear dash panel. Remove housing from vehicle.
  4. Remove heater core to housing retaining screws, then the heater core, Figure 2.
  5. Reverse procedure to install.
ad4c27d.gif

Figure 2

Personally, I'd pressure test the cooling system then look at the heater core to see if it leaks. It may just be a loose clamp or leaky hose.

Also can check the forum jpmagazine.com

I hope help you; good luck (remember rated this).

Sep 15, 2009 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
1996 Chevrolet S-10 Pickup Logo

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...