Question about 2000 Ford Mustang

1 Answer

Is replaceing front bumper and reinforcement and fender a do at home project

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,800 Answers

If you have the tools and another person to help you, no problem. It will take just an afternoon of work .

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

Where is the airbag impact sensor on the fender


Not too sure but the last time i checked it was on behind the bumper on the reinforcement bar or bumper support that goes from one side of the frame to the other and i belief their was a recall on that.You could also ask your dealer for a diagram.

May 27, 2014 | 1995 Chevrolet Monte Carlo

1 Answer

Replacing a front bumper reinforcment bar and radiator support on 2003 toyota corrolla


http://www.toyotapartszone.com/
Here's a Toyota site to get your parts,they will show pictures,it's best to have your vin number.

Oct 13, 2012 | Cars & Trucks

1 Answer

Can u replace vw beetle radiator, without removing front fenders ond nose. bottom plastic moldimgs are gone


NOPE YOU HAVE TO REMOVE FRONT FENDERS AND BUMPER COVER. REASON YOU HAVE TO REMOVE FENDERS AND BUMPER COVER.YOU CANT REMOVE RADIATOR HOSES AND REMOVE COOLING FANS.FENDERS AND BUMPER COVER IN THE WAY.

May 21, 2011 | Volkswagen Beetle Cars & Trucks

1 Answer

What parts are needed for replacing the front end of a 2001 monte carlo? I find bumper covers, reinforcements, energy absorbers, etc. Do I need some or all of these?


It depends on how far in the damage goes. Usually fenders, hood, bumper cover and headlights, but if the damage is deep, you could need a bumper, absorbers, the bumper mounts, even the radiator support assembly, which requires welding.

Pull off the damaged parts and set them aside, and then go to gmpartsdirect.com and click on the catalog link, fill in your make and model and look for the bodyparts you need to replace.

Apr 04, 2010 | 2001 Chevrolet Monte Carlo

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

The front of my vechicle went into a snow bank last night due to the slick streets and as a result, the front bumper is now pushed up. How do I realign the bumper?


you can take the bumper cover(plasic part of bumper) off and try to realine the bumper reinforcment (the steel part behind the cover) but unfortunatly the reinforcment is most likly bent

Feb 10, 2010 | Chevrolet Impala Cars & Trucks

1 Answer

Front bumper of 94 cad eldorado slipping on driver side - need to


There are 4 points of attachment for the front bumper. The nose has two long bolts that go through each of the 2 horizontal shock absorbers and screw into clips attached to the bumper reinforcement. You can access each bolt head with a long socket extension inserted in front of the fog lights.

The remaining two points of attachment are on the side of each of the front fenders, they are plastic guides that meet up with groves on the inside of the bumber sides, as you slide the bumper onto the reinforcement bumper, you line up the bumper groves with these plastic fender-mounted guides and you will reach a point where the bumper snaps in place.

I suspect the driver side bumper sliped out of the inner grove (best caes scenario), or the bumper goves cracked or the plastic fender-mounted guide cracked.

Get under the car to take a look, alternatively undo the 2 front nose bolts and remove the bumper, actually not a big job, and you will then be able to assess the problem.

Hope this helps.

Apr 05, 2009 | 1994 Cadillac Eldorado

1 Answer

Radiator in 1984 300zx


Maybe a little late, but you have to pull both fender liners so it is easier to get to the 3 nuts that hold the bumper to the fenders. There are 2 bolts that hold the bumper to the frame, one on each side underneath. There are 5 bolts that support th bumper to the reinforcement bar. It helps if you remove the air filter box. Once you removed the air filter box you need to remove the other 4 bolts from the second hood latch. The bumper should be ready to remove.

Jul 19, 2008 | 1984 Nissan 300ZX

Not finding what you are looking for?
2000 Ford Mustang Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...