Question about 2000 Ford Mustang

4 Answers

Vibrates the car runs very good the only thing is that it vibrates alot engine is 3.8 dont want to drive it like that do you gus know what cuold be creating this problem/ ?

Posted by on

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

My 2000 mustang 3.8 also had a bad vibration. after many trial and errors we replaced the harmonic balancer..not too hard but requires the "special" tools...and you have to buy it from the manufacturer. my car ran like a dream.

Posted on Feb 18, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,206 Answers

Your drive shaft has a bad universal joint and must be replaced.hope this helps you

Posted on Feb 07, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

Hi
The reason for vibration is that the engine mounting bushing has been worn off, hence the vibration is transferred from the engine to the car chasses
Get a new engine mount bushing.
Regards
Berry

Posted on Feb 07, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 645 Answers

Put car in gear while holding the break pedal give it some gas see fi the motor jumps up. Do the same in reverse, Make sure you are stepping on the brake when you do this. If the engine jumps quite a bit you need to replace motor mount.

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It looses power when going up hills and produces alot of smoke.


Hard to say, and there doesn't seem to be any indication of rain coming soon. But fire crews are working on the issue.----------------------------------------------------------------------------
vas 5054a v19

Nov 30, 2012 | Cars & Trucks

1 Answer

Vibration in the front end


a vibration could be a few things from a bad tire a tire not ballenced right, bad tie rod or tie rod end, a ball joint bad struts, sway bar , swaybar end links, or a bad hub and bearing, if you dont know what you are looking for the best thing to do is take it to a shop and have the diagnose is, it will be a lot cheaper then replacing alot of parts until you replace it, heres a tip if the vibration is only when you are driving fast and its only btween a 5mph range then you need your tires ballenced

Mar 26, 2012 | 2002 Pontiac Grand Prix

1 Answer

My car vibrates really bad when im in drive, park, neutral, and low, but will often make no sound in reverse. When I hit the gas it sounds like my cars engine is going to fall right out, especially when i...


The lincoln had problems with the engine mounts, the first thing i would do is to have all the engine and trany mounts checked and also the front suspension, i dont think its the running of the motor because the check engine light is not on, so it would have to be a mount type problem good luck, hope this is helpful.

Nov 03, 2010 | 2007 Lincoln MKZ

1 Answer

Wondering why i pull off at a light and its ALOT of vibration, when it's in neutral it doesn't vibrate. But when it's in drive it vibrates. What is the problem?


Good Evening, I can certainly understand your problem. I have seen this a number of times. The first thing to have checked out is your motor mounts (as long as your engine is running smooth I would not say a misfire) the mounts get a good amount of wear and tear and what happens in drive it relies on those mounts to help cushion the movement of the engine. I hope this of some help.
Thanks,
Joey

Sep 10, 2010 | 2001 Mitsubishi Galant

1 Answer

I have 1990 saab 900 turbo, it is vibrating a lot when i accelerate after 50 mph, wheels are balanced, its definitly a power related thing and the exahuast shakes alot also from this vibration....bit of a...


Hi John:

First suggestion would be to have the three engine mounting bushings checked out, these dampen the normal engine vibrations and if they have failed (gone soft, perhaps from contamination by oil, or just age) they don't restrain the engine. Polyurethane is possibly the best replacement.

I'm assuming that there are no other problems with the engine through it's rev range, until you get to that speed? And that the engine otherwise runs smoothly, even after that speed?

The other possibility is imbalance in the axle half shafts. Did you have the wheels balanced on the car? That might balance all the rotating parts.

Let us know.

Good luck!

Saabreur

Jul 11, 2009 | 1998 Saab 900

1 Answer

Whenever I turn on my car there is alot of vibration from engine


bad engine mount make car shake.cylinder misfire make engine shake.

May 10, 2009 | 2000 Mitsubishi Eclipse

1 Answer

Hyundai Tuscon, with v6 engine cuts out when driving


cuold be the fule pump stop working some time if take u many time crank after it stop.
or cuold be the crank postion sensor CKS if its start dairect

Mar 15, 2009 | 2003 Hyundai Tiburon

2 Answers

Car stoped running ck/time belt not broke,fuel comes out of


you may need a scan tool to find out why it died but the oil could be a number of things do you have to add oil alot

Nov 13, 2008 | 1998 Ford Escort

1 Answer

3.3L engine jumped timing


sound like compression ring gone pressure goes in oil if noise i dont think it worth to fix that motor a good second hand one there gone engine normally hope it FIXYA our problem thanks pierre

Jul 04, 2008 | 1999 Dodge Grand Caravan

Not finding what you are looking for?
2000 Ford Mustang Logo

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...