Question about 2001 Dodge Stratus
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: serpentine belt diagram:
The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.
Posted on Jul 18, 2008
cam shaft timing marks on back of cams ,two slots ,use a flat piece of metal to align .remove no1 spark plug and drop long thin screwdriver down it to bring piston just below tdc,then align cams so both cams are on the rock (valves closed) with knob on back cam aligning with pick up sensor left side between lobes.then bring piston up to tdc and fit belt.turn engine over twice with socket on bottom pulley to make sure no valves clear pistons.Remember to remove flat edge from back of cams i didnt last time and bent my home made tool
Posted on Jan 28, 2009
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!
Posted on Jan 22, 2010
My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.
I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.
CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
Posted on Mar 08, 2010
Tips for a great answer:
Jul 31, 2016 | Cars & Trucks
Below is the master help link
provided to go through belt routing diagram:---Timing belt, drive belt,
serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all
types of car models?
Click the link below: ----
----------This will help. Thanks.
Jan 25, 2012 | 2006 Dodge Stratus Sedan
Jul 20, 2011 | 1996 Dodge Stratus
Fig. Serpentine accessory drive belt routing-3.0L (VIN S) engine
May 05, 2011 | Ford Taurus Cars & Trucks
Apr 15, 2011 | 2001 Dodge Stratus
Apr 09, 2010 | 2005 Dodge Stratus
Apr 07, 2010 | 2001 Dodge Stratus
Oct 02, 2009 | 2004 Dodge Stratus
Jun 04, 2009 | 2001 Dodge Stratus
Feb 21, 2009 | 2003 Dodge Stratus
356 people viewed this question
Usually answered in minutes!