Question about 1986 Mazda 323

Open Question

Where do I top up my Mazda rustlers gearbox oil?

Where do I top up my Mazda rustler's gearbox oil?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 1997 mazda rustler 160i wheel bearings

buy a chevy

Posted on Dec 19, 2008

Ad
WildBill49
  • 97 Answers

SOURCE: mazda rustler 160i

Hi Gerrie1974-

WildBill49 here......Not knowing the specific year and version of your Mazda, I cannot give you a specific part at fault, but I can help you. I am assuming we're talking about an electronic distributor single coil ignition system

If the spark is weak directly out of the coil (with a known good coil hooked up with correect polarity), then the problem is in the spark trigger module... There is a variety of designs, but the basic components remain the same. This is the part of the ignition system that replaces the breaker points. It consists of two parts - a magnetic spark trigger sensor, and a spark signal amplifier/controller. these are sometimes combined into one ignition module.

Replace this module, and spark from the coil should be strong! If it is still weak, reverse the two wires to the coil.

Weak spark at the plug wire with the above good indicates distributor cap/rotor replacement time...

Gerrie, I hope this is what you are looking for, best of luck, and if you feel my advice worthy, please rate it!!!

Thanx-
-WB

Posted on Jun 22, 2008

  • 1 Answer

SOURCE: mazda rustler 160i wheel bearings

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Posted on Dec 17, 2008

  • 66 Answers

SOURCE: Somone tried to steal my son's Mazda Rustler last

I'd bet that they blew the fuses that feed the starter/ignition as well - Locate the interior cab fuse box, and with the key in the "on" position. go through it with a test light (one end grounded, pointed end to each side of each of the fuses) and ensure all the fuses are good (if one side illuminates, both sides should, but not all of the fuses will be hot) - I'd also look under the hood and check the fuse links and other main fuses located there as well - -I'd bet you'll find one or more of them is bad or blown...Hope that helps...Hope you find it - Damn thieves...

Posted on Sep 13, 2009

Testimonial: "Thanks for the feedbackI'll try it"

  • 1 Answer

SOURCE: where do i get fuel pump in mazda rustler 160i

fuel pump located inside petrol tank,
you have to remove the fuel tank, only 4 bolts, and a few pipes.
befor doing so, check fuel pump relay located in the middle of dashboard on the floor(horse shoe type plastic cover)

Posted on Nov 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much gear oil should l put , mazda rustler 1400 1991 gearbox


How much gear oil should must i put in a mazda rustler 1600

Jun 04, 2016 | Mazda Cars & Trucks

1 Answer

What's your question?how much is a starter 's solenoid for mazda rustler '97 model b6 engine


Seems as if you might want to call a parts store for this information.

Jun 24, 2015 | Mazda Cars & Trucks

2 Answers

I have replace the clutch on my rustler but it


Bleed the hydraulic system. Check the hydraulic lines, it could be swelling, Did you change the pilot bearing as well? If it was removed and not replaced, there will be a hard vibration.

Feb 18, 2010 | 1989 Mazda 323

1 Answer

Mazda rustler 160i wheel bearings


a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Dec 03, 2008 | 1997 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...