Question about 2002 Chevrolet Monte Carlo

1 Answer

The wiper blades are in up position,it will not reset back down

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

The entire blades pull off a threaded nub - Do so, and simply adjust the wipers to the correct position and push them back on.

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have replaced a wiper motor. My wipers are going in the down direction instead of up when it tries to reset. How do I fix this


Michael is correct, Remove the Bolt, Allow it to go to the SEATED position and then you will be good to go

Apr 10, 2013 | 1992 Geo Prizm

1 Answer

Wiper blades stuck in upright position


there is 2 switches in the wiper motor a run and a park sounds like one of them has failed or the wiring to them but check the switch first may have broken wires

Sep 06, 2017 | 2000 Buick Century

1 Answer

I need to have 'step-by-step' instructions for replacing the driver side windshield wiper arm on my 2000 Ford Explorer. Can you help me with this?


  • Turn your wipers off, using the stalk on the left side of your steering column. Turn your ignition off and remove the key.

  • 2

    Pull the wiper blade up to lift it to the service position. Pull the front part of the blade down to position it at an angle.

  • 3

    Pull back the lock pin on the center part of the wiper blade (where it connects to the wiper arm). This unlocks the blade from the wiper arm.

  • 4

    Grasp the blade on each side and pull it down (away from the extended wiper arm) to release it from the "U" clip.

  • 5

    Repeat the process for the other wiper blade, if desired. Removing the driver's side and passenger's side wiper blade is the same.

  • 6

    Install the new wiper blade. Open the lock pin on the new blade, and then insert it into the wiper arm "U" clip. Close the lock pin and lower the wiper blade to its normal position.

  • Jan 29, 2011 | Ford Explorer Cars & Trucks

    1 Answer

    Volvo s40 2000 has 2 wiper blades, 1 has stopped working altogether, the other stops in random places when turned off...that is it doesn't return to normal resting position. do i need new wiper motors...


    there is one wiper motor,in the off position,reset yuor wiper arms and tighten the nuts that hold them down on the mounting points of your wipers

    Oct 12, 2009 | 2000 Volvo S40

    1 Answer

    I cant figure out how to change my windshield wiper blades on 2001 ford ranger


    How to Replace Wiper Blades Guide (Typical):
    Potential tools needed to replace wiper blades:
    • Flat blade screwdriver (small)
    • Small nosed pliers
    • Latex or vinyl gloves
    • Safety goggles
    To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
    • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
    • Step 2: Locate the mounting clips at the top pivot on the wiper blade
    • Step 3: Release the clip and remove the wiper arm
    • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
    • Step 5: Reinstall the new wiper blade and recheck wiper operation

    Common Problems:
    • Make sure the wiper blades are the same size as the original blades.
    • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
    • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
    • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

    I hope help you with this (remember rated this help) Good luck.

    Sep 16, 2009 | 2001 Ford Ranger Regular Cab

    2 Answers

    How do I remove front wiper blades to replace with new ones on my 2006 nissan quest


    How to Replace Wiper Blades Guide:
    Potential tools needed to replace wiper blades:
    • Flat blade screwdriver (small)
    • Small nosed pliers
    • Latex or vinyl gloves
    • Safety goggles
    To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
    • Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
    • Step 2: Locate the mounting clips at the top pivot on the wiper blade
    • Step 3: Release the clip and remove the wiper arm
    • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
    • Step 5: Reinstall the new wiper blade and recheck wiper operation

    Common Problems:
    • Make sure the wiper blades are the same size as the original blades.
    • When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
    • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
    • Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

    I hope help you with this (remember rated this help) Good luck.

    Sep 14, 2009 | 2006 Nissan Quest

    1 Answer

    Wiper was pushed down from the parked position


    you will need a flat screwdriver about 5/16 or 3/8's wide. to pry your wiper blade off. pull back on your wiper arm while prying with your screwdriver. work on both sides of your wiper blade, you will notice it starting to come off a bit at a time. just keep working it till it falls off.... good luck sawdust46

    Jul 25, 2009 | 2007 Nissan Murano SE

    1 Answer

    1997 Checy wiper issues


    there is a circuit inside the wiper motor called the park circuit, it is what parks the wiper blades in the proper position on the windshield, it is defective. on your car it is park of the wiper motor assembly.

    May 26, 2009 | 1997 Chevrolet Cavalier

    1 Answer

    Wiper blades won't go back down. Can we reset the motor?


    U jhave damaged what is called the wiper motor park circuit, u will need to replace the wiper motor assembly.

    Feb 03, 2009 | 1996 Dodge Caravan

    Not finding what you are looking for?
    2002 Chevrolet Monte Carlo Logo

    Related Topics:

    128 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8265 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...