Question about 2005 Chrysler Town & Country

1 Answer

Chrysler T&C (2005) - Can anyone describe how to access, remove, and replace the bulb in the crescent-shaped reading lights at the front of the overhead console. The owner's manual says nothing, and there are no obvious clips, latches, screws, etc. to release.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 149 Answers

Start at the front towards the winshield with a very small flat headed screwdriver. Getting under the lip of the light cover in the front pop the 2 front clip down in the front. Do Not do this on the seat side or you brake the clip that turn the light on/off. After poping the front down, side out towards winshield. The blub removes by turning counterclockwise. Blub is a 578

Posted on Feb 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i get to my low beams on my chrysler 2005 sebring sedan i got to the high beams perfect but the low beams right next to it has a metal barrier surrounding it which makes it impossible


Unfortunately, the answer I have is not a happy one =(. My wife has a 2005. In order to replace the bulb you will have to pull the Crutons (plastic push pins) that hold the front bumber cover on, remove the Headlight housing & replace the bulb that way. Shame on Chrysler for making it so difficult, in my opinion. But I hope this helps you to change the bulb =)

Aug 26, 2011 | 2004 Chrysler Sebring

1 Answer

How do you change the bulb in the driver's side front dome reading light


On teh back of the headlight housing there is a interlocking bulb holder that your wires are attached to. Disconnect the wires, Unscrew the Bulb holder and replace old bilb with new one. Reassemble and reattach the wire socket.

its works in 2001 chrysler.. hope so it works in 2005 model also

rate it if it resolves your problem

Jan 08, 2010 | 2005 Chrysler Town & Country

1 Answer

Is it easy to replace the rear turn signal and brake light bulbs on a 2005 Pacifica? Do you access the screws from the hatch?


You can access screws from hatch behind liner. there should be two screws for each lens. Bulbs and socket just turn and remove.

Aug 25, 2009 | 2005 Chrysler Pacifica

1 Answer

Describe your 2005 Chrysler Town &


check the bulbs do not have fractured filaments,and check the headlamp relay.check the sockets for corrosion and if all that checks out ok check the connection on the back of the headlight switch and the daytime running light module

Aug 15, 2009 | 2005 Chrysler Town & Country

1 Answer

Side Marker Bulbs


you need to remove entire assembly to access bulbs.it is secured by small hex head screws & a ''sliding tab'',an L shaped piece you pry up w/a flat screwdriver.

Jul 30, 2009 | 2005 Mercury Mariner

4 Answers

Replace headlight bulb on 2005 Chrysler Sebring.


NO NO! Just reach in with hood open and turn the plastic ring that holds bulb and harness in. Then you can just pull it out and replace it.

Jul 06, 2009 | Chrysler Sebring Cars & Trucks

1 Answer

2005 town & country reading light


I have the same vehicle. when the sun comes up I will go out and look my self and get back. It should let me post a follow up.

Jun 17, 2009 | 2005 Chrysler Town & Country

5 Answers

How to remove/replace headlight bulb


I just replaced the bulb in the driver's side headlamp on my 2005 Scion xA without having to remove any screws, bolts or the grill. It's very simple, but it helps to have small hands. Just take the cover off the fuse box to allow more room for your hand. Reach in with your left hand and unplug the wiring assembly. Remove the rubber cover by using leatherman pliers. Squeeze the two sides of the spring clip together to release the bulb. Don't worry, the spring is hinged at the bottom, so you won't lose it. Take out old bulb & replace with new. Reverse steps, making sure you align the center hole of the rubber cover so that the three prongs of the bulb are protruding.

Nov 25, 2008 | 2005 Scion xA

1 Answer

Replace ford escape turn signal front 2005


you should not have t remove the headlight assembly to replace the bulb access should be under the hood. as for the moisture the bulb holder may be damaged or not fitted properly

Oct 16, 2008 | 2005 Ford Escape

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...