Question about 2002 Jeep Grand Cherokee

1 Answer

I am trying to remove the dash in my Jeep, and I see no more screws or bolts, and it wont pull out. it appears there is something holding it behind wher the stereo was. This is after the dash shell is off.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

You can find the info you are looking for WJJEEPS.com. I did this very job to replace my heater core, and this website had a step by step proceedure. Look in the sections related to heating and cooling, etc. Believe me, this information was a lifesaver. Good luck.

Posted on Feb 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parking lights dash lights plate lights not working


Check the fuses first, then if they are ok you may have a defective headlight switch, they connectors can get burned and the switch contacts as well this can cause the loss of lights like you have. Replace the headlight switch and connector as one repair, do not crimp connect the repair connector on, solder and shrink tube the solder joints. To remove the headlight switch for inspection follow these directions.
Remove two bolts under the radio and pull out that bezel

Remove four 9/32 bolts (or screws seen vehicles with bolts, some with phillips screws, some hex screws) on the very bottom of the panel by your knees (two hidden under the hood release handle)

Remove two bolts right behind the top seam of that panel under the steering wheel holding the top panel to the dash (you should be able to pull the steel panel by your knees down slightly to get to them, but you may need to remove or loosen yours, depends on if someone has had it off before)

Remove the three bolts holding the top cover inside the upper lip by the instrument cluster then you can remove the dash panel holding the switch

Sep 14, 2012 | 1997 Ford Explorer AWD

2 Answers

How do i remove the factory radio on my 1983 cadillac fleetwood


Hi there,

Locate and remove two (2) phillips screws that secure the top of the plastic panel that surrounds the radio. The plastic dash panel will pull off once the screws are removed as shown in the photo above.
The front of the radio is held in with two (2) 7mm bolt screws at the top of the radio. Remove the 2 bolt screws.
There is a hidden radio that secures the rear of the radio and is located under the radio. Pull the ashtray to its extended position. You will need to lay on your back or side and look behind the ashtray, up to the bottom of the radio.
Once the ashtray has been pull to its extended position, you should be able to locate and remove one (1) 7mm bolt screw as seen in the photo above.
Once all screws have been removed, the radio can then be removed. Pull firmly on the radio to remove it from the dash. The radio will most likely resist pulling from the dash. The antenna cable which plugs into the rear of the radio is very short and gives the radio resistance when trying to pull the radio out of the dash. Continue to pull firmly and the antenna cable will unplug itself as the radio is pulled from the dash.
Unplug (1) blue, (1) white, and (1) black wire harness connector(s) from the rear of the radio. There will also be wires extending from the rear of the radio with a plastic connector attached to the wires about 4 inches from the rear of the radio. Unplug this small connector. The radio can now be completely removed from the dash. Set it aside. You will need to remove the plastic brackets attached to the top and bottom of the GM radio. This will be shown in detail in the "Mount New Radio" section.

Hope these helps....

Jan 23, 2011 | Cadillac Fleetwood Cars & Trucks

1 Answer

1995 jeep grand cherokee tach light is burned out. The rest work fine. How do I fix it?


you must remove the cluster heres some diagrams to help you. hope this helps, dissconnect battery,then remove ash tray,remove center bezel screws,remove bezel,now remove screws for holdingdash pad behind top of center bezel, pry defrost grill out of dash unplug sensors and set aside,remove screws holding dash pad to defrorst duct and cluster,open glovebox and remove screws holding pad, remove pad,pop out has clips holding,remove screws from cluster pull cluster up and out enough to unhook connector. heres some diagram to help.ab9f0ee.gif0b7cf5b.gif1ddb17d.gif

Feb 11, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How do i remove a radio from a 2005 toyota Sequoia? More specificaly, how do you remove the dash trim around the face?


There is an AC vent on either side of the radio. Push the vent in on the top, so that the vents are aimed upwards.

You will not be able to see two philips screws just above the vents. Remove them.
Some knob type AC units have a screw behind the center AC knob as well, that you can pull straight off.

2004 I *believe* should have the push button ac and no bolt on the bottom.
Once the screws are out, the bezel will pull straight off, unplug the wires then set aside.

The radio has 4 10mm bolts or philips screws holding it in (some bolts had a philips cut on them as well).
Remove them and pull the radio straight out, unhooking the cables/antennas

Oct 28, 2009 | 2004 Toyota Sequoia

2 Answers

How do you take the dash off of a chevy cavalier


-well you start by removing the covers at each end of the panel. you will see them when you open the doors, they will just pull off.
-then you will remove the defrost grill in the top center of the dash.
-there wil be two 7 mm bolts behind the grill you will need to remove
-each end of dash will have a 7 mm bolt
-open glove box and you will find three black 7mm
-hidden up left in the glove box a square cutout you will find two silver or gold 7mm bolts that will have to be removed. (these two remove the airbag cover.
-once all the screws are removed then just pull the upper dash panel upwards to remove it (be careful of the airbag itself not to puncture it)
-with the top half of the dash off you will find 4 more 7mm bolts holding the facia part of the dash.
-remove these and pull the dash towards you around the heater and radio the dash is clipped in. be careful not to crack the panel.

-reverse procedure to put it back together.

Aug 30, 2009 | 2003 Chevrolet Cavalier

4 Answers

Where is the flasher on a 1994 toyota previa


The flasher is bolted to the firewall behind the right side of the instrument panel and you can't get to it from underneath the instrument panel. You will have to remove the center console fascia to get to the instrument cover screws and remove the instrument cover. Then you can get to the instrument holding screws and move the instrument panel out of the way. Either a service manual or AutoZone.com will have this information and pictures. Replace the flasher with a genuine Toyota flasher relay. The aftermarket relays might look like they fit but I have found out they don't work properly. The flasher is bolted to the firewall with a 13mm bolt. Take out the bolt and replace the flasher.

Jul 15, 2009 | 1997 Toyota Previa

1 Answer

Trying to remove dash to install speakers.


makesure they are all removed and that its just not sticking i had the same problem and found out after all the bolts were removed that it was just rusting and corroded good luck

May 31, 2009 | 1990 Jeep Wrangler

3 Answers

98 Malibu Theft control ignition shut off activates when starting the car


with the 1998 anti theft what would the dealer do that a different wont do .the anti theft light id on on car wont stay on..i need help.ami1998

Jun 26, 2008 | 1998 Chevrolet Malibu

1 Answer

Cd player


remove ash tray one screw behind there, then remove top dash panel that goes from end to end across dash this just snaps off pull upward to remove you will see 2 screws on top of trim around radio remove these 2 and then dash trim will pull off pull straight back then radio can be removed should be held in by 2 10mm bolts, this should cover 80% of the radios (important TIP) if it still doesn't come out the trick is some of the wranglers have an extra security bar on stock cd players only you will see 2 more 10mm bolt on the top of the dash where you removed the 2 screws from earlier these hold a bracket that is mounted to the back of the cd player once they are unbolted you can remove the radio it takes some pulling and tweaking of the brackets but it will come out

Jun 12, 2008 | 2002 Jeep Wrangler

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...