Question about 2006 Chevrolet Silverado

1 Answer

I installed a new power steering supply line on my 2006 siverado and now I only have manual steering. What's wrong ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 200 Answers

Slowly turn the steering wheel from maximum left to maximum right turn. Keep doing this several times with the engine running to purge the air from the system. Keep the P/S fluid filled while doing this.

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

2 Answers

What kind of power steering and brake fluids do I use on a 2006 town and country van?


You can use any fluid marked as power steering fluid. (not transmission fluid) Use dot3 brake fluid in brake systems. Don't use synthetics in brake systems unless system has been completely disassembled and cleaned.
For better service life, remove brake fluid from reservoir with a turkey baster once a year and refill with new fluid (no bleeding required) You can also drain power steering and re-fill every two years by removing return line to pump, allowing it to drain, then re-connecting and re-filling. Nothing lasts forever, but this helps it last a lot longer.

Aug 08, 2009 | 2006 Chrysler Town & Country

1 Answer

How do i install my power steering return line


With the engine cold, loosen the steering reservoir filler cap to allow air into tank. Take the lowest fitting loose and let it drain into a bucket under the vehicle. When finished draining remove Line fitting at reservoir. Remove any brackets holding the line in place and remove line from vehicle. Take the line to automotive supply and buy proper replacement using old line to verify fit. Purchase enough recommended power steering fluid to replace what drained into bucket. Install new line in reverse of removal steps making sure seals (washers and/or "O" rings) are properly installed. Dispose of old fluid safely.
To fill reservoir and line: While filling reservoir with engine running turn steering wheel from left to right until wheel stops. Continue filling and turning until all air is out of system and reservoir is at the proper fill level. Check for leaks.

Mar 23, 2015 | 1988 Cadillac Eldorado

1 Answer

Power steering pump Ford Focus 2006 DIY Manual


its quite quite simple;take your pipes of and block them off reconnect them to new pump and replace pump to in line belts.adrian;;;

Nov 14, 2009 | 2006 Ford Focus

3 Answers

How do you remove the Power Steering Pump and bracket. I have taken off several bolts but it still is not letting loose. Help


3.0L (VIN 3) Engine

f799ffc.gif
Power steering pump mounting detail (3.0L engine)

  1. Disconnect and isolate the negative battery cable.
  2. Remove the accessory drive belt. The belt does not have to be removed from the engine.
  3. Raise and safely support the vehicle.
  4. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  5. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  6. Place a drain pan under the power steering pump. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  7. Remove the accessory drive belt splash shield.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 2 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly out from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 2 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the 2 support bracket mounting bolts to 40ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

3.3L (VIN R) & 3.8L (VIN L) Engines

0b3de97.gif
Rear support bracket mounting detail (3.3 & 3.8L engines)

6764c64.gif
Power steering pump mounting detail (3.3 & 3.8L engines)

  1. Remove and isolate the negative battery cable.
  2. Raise and safely support the vehicle. Place a drain pan under the power steering pump.
  3. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  4. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  5. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  6. Remove the accessory drive belt splash shield.
  7. Remove accessory drive belt.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 3 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 3 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the support bracket mounting bolts to 40 ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. Torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

Nov 03, 2009 | 1997 Chrysler Town & Country

1 Answer

Diagram for for power steering pump high side


what year? what engine?

Installation
  1. NOTE: If a new power steering pump is to be installed, the unions that are supplied fitted to the pump should be removed and saved for future use.
    Using the special tool, install a new O-ring seal.
    1. Push the new O-ring seal onto the special tool.
    1. Locate the tool over the union and ease the O-ring seal onto the union.
8675655.gif

Oct 07, 2009 | Mercury Cougar Cars & Trucks

1 Answer

Change powers steering pump


Hi, this is a step by step guide that will help you within your replacement of this device.

Step1
Loosen the drive belt and slip the belt over the pulley. Use a suction gun to **** out as much power steering fluid as possible. Place a drain pan under the pump and disconnect the lines and fluid return hose. You may need to remove the air cleaner housing to access the return hose. Allow everything to drain completely.
Step2
Cap the ends of all the lines to prevent leakage. Remove the mounting fasteners and detach the pump from the engine. You should be able to pull it free from the car completely and take a moment to inspect it and see what went wrong. You could then prevent the demise of the new power steering pump by addressing the source of the problem.
Step3
Measure how far the pump shaft protrudes from the face of the pulley hub, if it is necessary to remove the pulley to access the pump, as is the case with some engines. This assembly will need to be reinstalled to the correct positioning after the new pump is installed.
Step4
Install the new pump using the reverse removal procedure and make sure all fasteners are tightened securely. Also, take a moment to bleed the power steering system according to the directions in your repair manual. For specific instructions on the reassembly of some items during this process, consult your repair manual as each engine has its own specifications.

Please rate and have a great day:)

Apr 23, 2009 | Oldsmobile Intrigue Cars & Trucks

1 Answer

No power steering new installation


disconnect the return line at pump put it in a jug start the engine check for cirrulation and too bleed air keep filling pump if you have no cirrulation the reconnect the return hose and discnect the supply too see if it pumping if it is then you have a blockageif not then you may have a bad pump

Mar 04, 2009 | 1993 GMC Sierra K1500

1 Answer

Power steering repair


www.autone.com
select repair info
choose your car
see anything you want

Dec 27, 2008 | 2006 Ford Focus

Not finding what you are looking for?
2006 Chevrolet Silverado Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...