Question about Chevrolet Tahoe

1 Answer

How do you change license plate bulbs on a 99 chevy tahoe?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

They should pull out of the bumper from behind, turn them 1/4 turn left and pull out the socket.

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plate light does not work, but lights are good and sockets seem good


check bulb the number plate light runs on the same circuit as the side lights so if they are working its got to be a bad earth on the plate light

Jan 24, 2016 | Cars & Trucks

1 Answer

My 2005 chevy tahoe 5.3 license plate light went out i replaced bulbs problem still there what is the fuse labeled for that circuit?


Check the brake bulb socket for short , clean replace bulbs , check connector to rear licence plate lights . Also trailer harness for short , all on same fuse circuit .

Jan 23, 2013 | 2000 Chevrolet Blazer

1 Answer

License plate light will not stay on this for a 2007 chevy tahoe,what do i have to disassemble to check wiring


Hello,

If you notice should be a couple small screws to remove lens to get to bulb. A lot of times it just a loose bulb or the prongs on end of bulb that hits the copper connection. First take bulb out, replace it, even though it works, but new one would have nice new connection, and before putting it in, spray inside where bulb goes with electrical cleaner can get at any auto supply, then put in. Should work. On a 2007, it is unlikely there is a ground problem, but if so, after trying this, get back to me and I will tell you how to check wires and what to do. Thanks Mike


10_5_2011_3_47_10_pm.png

Oct 05, 2011 | 2007 Chevrolet Tahoe

2 Answers

Bulb out for light to see license plate on 2oo2


You need to go under the rear bumper and you will see the connections.Just twist counter clockwise and it should come out.Hope this helps.Good luck.

Mar 31, 2010 | 2002 Chevrolet Tahoe

1 Answer

Where is the fuse for the license plate bulbs of a 2002 Chevy Tahoe


the headlamp switch controls the license light. the filament in all bulbs react as a fuse when shorted out. replace the bulb

Feb 20, 2010 | 2002 Chevrolet Tahoe

1 Answer

Changing license plate lights on 2004 chevrolet


the light can be replaced from the back side of the light housing . go under the back side of bumper under the truck behind lisence plate you will see the where the wire goes to the light . grab the housing not the wires and twist about a half a turn and pull gently. it should come out and then remove the light bulb and replace with new

Jan 28, 2010 | 2004 Chevrolet Tahoe

2 Answers

99 Chevy Tahoe... Rear turn signals, brake lights, and hazards


I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Oct 10, 2009 | 1999 Chevrolet Tahoe

1 Answer

How do you change brake light on a 99 chevy tahoe


I Do Believe that the Light Assembly Comes OUT Via TORX Screws and The Lights are On a Curciut Panel that is then Removed to Gain Access to Bulbe

Aug 05, 2009 | 1999 Chevrolet Tahoe

1 Answer

License plate bulb 99 alero


remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

1 Answer

License plate bulb


right above the plate the bulb should be.

Nov 23, 2008 | 1997 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...