Question about 1991 Chevrolet Silverado 2500

2 Answers

How to install a starter on a 1991 chevrolette silverado

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

Disconnect battery,,crawl under passenger side of truck,,some mechanics take wires off starter first,,some pull the to starter bolts out,,& then disconnecting the wires,,( u should never let stater hang by the wires,the battery wire nut either 13 mill or 15 mill ,,the smaller nut on solenoid 7/32 or 5/16 or metric..

Posted on Feb 07, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 617 Answers

2wd or 4wd, 1500, 2500, 3500, 4.3, 5.0, 5.7, 6.2, 7.4 ? need information along with email address to send directions to replace starter

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install starter relay for 1991 park ave


11_23_2011_2_35_06_am.jpg

Fig. 1 Starter mounting
  1. Disconnect the negative battery cable.
  2. Raise the vehicle and support safely.
  3. Disconnect the wiring from the starter.
  4. Remove the flywheel shields.
  5. Remove the starter retaining bolts and remove the starter from the engine.
To install:
  1. Position the starter against the engine and install the bolts. Torque to 35 ft. lbs. (47 Nm).
  2. Connect the starter wiring.
  3. Install the flywheel shields.
  4. Lower the vehicle and connect the negative battery cable.
  5. Check the starter for proper operation.
Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 22, 2011 | 1991 Buick Park Avenue

1 Answer

Where is the starter on a 1991 eclispse 2l awd turbo


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

Removal


  1. Disconnect battery cables, then remove battery and battery tray.
  2. Disconnect speedometer cable from transaxle.
  3. On models equipped with 1.8L/4-107 engines, remove intake manifold stay.
  4. On all models, disconnect starter wiring connections.
  5. Remove starter mounting bolts, then the starter.
Installation


  1. Before mounting starter, clean the mating surfaces of starter and the engine.
  2. Install starter and torque mounting bolts to 20-25 ft. lbs.
  3. Connect starter wiring connections.
  4. On models equipped with 1.8L/4-107 engines, install intake manifold stay.
  5. On all models, connect speedometer cable.
  6. Install battery tray and torque attaching bolts to 6-10 ft. lbs.
  7. Install battery and battery hold-down. Torque hold-down bolts to 1.5-2.0 ft. lbs.
  8. Connect battery cables.

Jan 02, 2011 | 1991 Mitsubishi Eclipse

2 Answers

2004 chevy silverado with new starter installed as soon as I reconnect the battery cable the starter engages without key even in igniton


It could be any of the following,

1. The field wire to the starter (the wire that is hot when you turn the ignition switch to the start position, and should be connected to the "S" on the solenoid) has the wire connector pushed over and touching against the main connection and battery cable on the solenoid, or has insulation missing somewhere on the wire and the exposed wire is touching together with an exposed wire from one of the constantly hot wires from the main battery connection on the solenoid.

2. The ignition switch is stuck in the start position (the switch itself, not the key and tumbler) however if you were not having a problem with the ignition switch before you replaced the starter then it is unlikely to be the problem.

3. The starter solenoid is defective. This does happen once in a while and you should be able to have the starter tested where you bought it from.

Apr 23, 2010 | 1991 Chevrolet C1500

1 Answer

Truck wouldn't start. Starter was bad; replaced


run a positive jumper cable from the + battery post to the starter post if it turns over replace battery cable. also check ground cable

Jan 15, 2010 | 1991 Chevrolet Silverado 2500

1 Answer

1991 Century Buick V6 starter replacement.


remove the positive battery cable from the post
remove the 3 wires from the starter and the two bolts holding the starter to the block.
reverse the procedure for installation.

Oct 07, 2009 | 1991 Buick Century

1 Answer

Trying to remove the starter on a 1991 SaturnSL


no there is not a special tool need more info go to collisionrepairadvice.com for more
1991 Saturn SL L4-1.9L DOHC VIN 7 Vehicle Level a_003366.gif Starting and Charging a_003366.gif Starting System a_003366.gif Starter Motor arrow1.gif Service and Repair arrow2.gif blnk_spc.gif Service and Repair Notes
  1. Disconnect battery ground cable.
  2. Remove air inlet tube and fresh air hose, on DOHC models, lift resonator upward to disengage from engine support bracket.
  3. Remove upper starter attaching bolt through access hole near intake manifold support bracket.
  4. Raise and support vehicle.
  5. Using suitable pliers, remove starter shield pin, then lift shield upward to release from solenoid.
  6. Disconnect starter electrical connectors and position aside.
  7. Remove lower starter attaching bolt.
  8. Remove rear starter support bracket attaching bolt.
  9. Rotate starter until bracket clears axle shaft support bracket, pull rearward toward lefthand side of vehicle to remove.
  10. Reverse procedure to install. Torque starter attaching bolts to 26 ft. lbs., starter bracket bolts to 22 ft. lbs. and starter solenoid terminal to 3 ft. lbs.

Apr 11, 2009 | 1991 Saturn SL1

1 Answer

I need to change my starter on a 1991 mercury sable


Starter are one of the easier mechanical engine parts to change.

1) DISCONNECT THE BATTERY.
2) Disconnect the electrical cable running to the solenoid on the starter.
3) Remove the two bolts holding the starter in place.
4) Pull the starter out.

To install another starter, do the above steps in reverse order in reverse.

Apr 04, 2009 | 1991 Mercury Sable

2 Answers

What procedures do I take when removing and installing a new starter? 1991 lexus ls 400


Let engine cool down, remove battery terminals (negative first, then positve), remove starter. Install starter, install battery terminals (positive first, then negative), start and check for proper operation (no grinding noise or squeling).

Apr 03, 2009 | 1991 Lexus LS 400

1 Answer

How to remove the transmission


If you do not know how this is a large job delicate between motor and transmission maybe you might reconsider and find on the ground beside you assistance?

Dec 27, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...