Question about 1999 Ford Crown Victoria

1 Answer

Changed coil pack wont start on  99 crown vic

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

Check the ignition module,and the crankshaft sensor.

Posted on Feb 06, 2010

Testimonial: "help"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can moisture cause my 98 crown vic to stutter and to not start?


That a questions with many answers, none the less moisture will cause the problem you are having. Things to consider , a full tuneup and filters. And check the coil pack too.

Mar 09, 2015 | Cars & Trucks

1 Answer

My 1996 Crown Vic. recently started to buck and backfire a bit, turned out to be a misfire on #4, have been looking into it with a bit of progress but not complete success


I have faced the same thing with my car, this is not a single answer to this problem. It could be a bad boot on the coil pack, it could be a improper coil install, sometimes the spring does not sit in well, it could be that the intake manifold is leaking, it could be that the egr valve is stuck, it could the exhaust manifold is leaking, sometimes these issues are not caught by the OBD 2 sensors, you can try to move the coils around to see if that works out.

Mar 17, 2014 | 1995 Ford Crown Victoria

1 Answer

My 2002 crown vic started backfireing then would not start seems to not be getting any gas could this be my coil pack?


It sounds more like a timing belt has failed.
check for spark at the spark plugs
If there is no spark you can have the coils tested
But i till think timing belt due to the back fire and then the no run
If this was helpful please rate this question

Jan 24, 2011 | 2001 Ford Crown Victoria

1 Answer

Trying to locate spark plugs on 99 crown vic police interceptor engine


They should be mounted down in the cylinder heads, you'll need to remove each coil pack. A long extension and 5/8in spark plug socket and an extendable magnet will help. Also, you may need to remove the fuel rail to get to move the coil packs.

Oct 17, 2010 | 2000 Ford Crown Victoria

3 Answers

I have a 2001 Focus that is showing a #3 misfire, changed the spark plugs and wires and it is still running rough? What next?


had the same thing with my crown vic on the #8 cylinder. changed plugs and wires. still missing. wound up replacing the coil pack. you can check resistence of the coil between companion spark plug towers. ford marks each tower with 2 cylinder #'s. resisistence should be around 10-12 ohms

Mar 15, 2010 | 2001 Ford Focus

1 Answer

Bad coil pack on crown vic


well if you have checked the spark plugs and they look good then its probly the coil If the plugs have never been replaced i would start with a tune up and see if this fixes the problem. If not there is no good way for you to test it you would need a computer to hook up to the car

Jan 24, 2009 | 2001 Ford Crown Victoria

2 Answers

Ford Crown Vic p0300 random cylinder misfire


take a look at the EGR valve it could be either vacum controlled or electronic either way what seems to be the problem is that the valve is stuck in the open position until the engine warms up you can gently tap the egr valve with a small hammer or a screw driver and you can see that it runs smooth, now if the egr valve is vacum controlled replace the valve. if it is electronoc controlled replace the valve and the module for the egr valve.

Nov 02, 2008 | 2000 Ford Crown Victoria

2 Answers

Engine light po 300 code


IS THIS A 99 CROWN VIC? IF SO IS IT MISFIRING? IF THIS IS THE CASE YOU MORE THAN LICKLY NEED PLUG WIRES.

Sep 06, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...