Question about 2001 Chrysler Sebring

2 Answers

I need to replace the throttle body sendsor on a 2001 chrysler sebring

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 617 Answers

Need further information so can give you right direction to replace your Throttle Body Sensor, Need to know if a Convertible, Coupe or Sedan and what motor? the 8th digit of vin also, i also can email you the directions with pictures if like, i would also need a email address to send pdf file to you

Posted on Feb 06, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Remove and replace with the screws a little loose. Next set the voltage to 1.5 volts with the accelerator cable at idle postion. Now your done now after checking the mount screws are secured

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission solenoid pack valve


if your refering to the solenoid pack in the valve body then you first drain trans, remove pan, remove old gasket(do not discard unless you have a new gasket or the old is reusable.) only remove bolts that are pertaining to the removal of pack and or vavle body, remember what bolts go where, an then install is reversal of removal.

Jan 25, 2014 | 2001 Chrysler Sebring

1 Answer

What the throttle body looks like and where is it located on 2007 chrysler sebring


follow the hose from the air filter to the engine and where it ends will be the throttle body assembly.

Jul 01, 2011 | 2007 Chrysler Sebring Sedan

1 Answer

How to replace air filter


what size engine? some of this at end of air duct tube from throttle body to air box has two big tabs, press them down and pull duct tube out let me know if this help

Nov 17, 2009 | 2001 Chrysler Sebring

1 Answer

How to change an EGR Valve on a 2001 Chrysler Sebring LXI Coupe


Looking at the engine from the front/top it is in the center between the firewall and the rear of the engine near the throttle input. actually very east to replace.

Aug 23, 2009 | 2001 Chrysler Sebring

1 Answer

How to replace engine air filter


  1. Disconnect negative battery cable.
  2. Disconnect inlet air temperature sensor electrical connector.
  3. Disconnect fresh air makeup hose from throttle body air inlet hose.
  4. Disconnect PCV hose from intake manifold.
  5. Loosen hose clamp at throttle body air inlet hose. Remove hose from throttle body
  6. Push in on locking tabs to disengage air inlet hose from air cleaner housing. Remove throttle body air inlet hose and air cleaner element together.
  7. Separate air cleaner element from throttle body air inlet hose.
INSTALLATION reverse

Jun 11, 2009 | 2002 Chrysler Sebring

1 Answer

Replace air filter 2002 Chrysler Sebring convertible 2.7L engine


you need to loosen the clamp on the throttle body and unplug the map sensor then there are two clips on the other end pull that out and you should be able to pull the filter out you don't need to take the box off.

Apr 10, 2009 | 2002 Chrysler Sebring

2 Answers

I have a 2000 Chrysler Sebring that wont idle. The car starts and will run only if I step on the gas pedal.


clean the IAC. Use spray carb cleaner and spray the idle air control valve. It is on the throttle body near the throttle plate. It may have become stuck with deposits.

Clean the throttle body as well. Check for vacuum leaks

Feb 05, 2009 | 2000 Chrysler Sebring

1 Answer

Throttle position sensor


its located on the opposite side of the throttle body as the throttle cable. remove the whole throttle body then remove the TPS from it.

Jan 15, 2009 | 2000 Chrysler Sebring

Not finding what you are looking for?
2001 Chrysler Sebring Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...