Question about Chevrolet S 10

1 Answer

Chevy s10 2003 will not engage in 4low or 4high. Push button switching into all, makes noise like it is transphering. But then when driving, only two rear tires will work.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

It might be the actuator located under the battery tray. look at that and see of it is ripped, torn, or the cable might have came loose.

Posted on Mar 13, 2010



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do I put my Chevy trail blazer 2005 LS in 4 wheel drive

look on the dash for a 4wd button or switch. may be located between the steering wheel and the radio. when you turn the knob to select 4hi, 4lo, 2hi, or auto, the indicator light above the corresponding selection will flash until the shift has completed. if the light stays flashing there is a fault in the 4wd system

Mar 20, 2018 | 2005 Chevrolet TrailBlazer

1 Answer

What is wrong with my 2000 chevy blazer ; it is a 4wd automatic an i locked it in 4wd low to pull my boat out of the water and can not get it to shift back i to 2wd?

You shouldn't have to use 4wd to tow a boat out of the water. Does your truck have a 2wd button or just the 4high and 4low button? If you have a 2wd button, put tranny in neutral and then hit the 2wd button. If you just have the 4high and 4low button, put the tranny into neutral then press the 4high button twice (Once to get back into 4high, then again to get out of 4high and back to 2wd).

Jun 04, 2014 | 2001 Chevrolet Blazer

1 Answer

2006 Hummer H3 4 wheel drive wont engage in 4high or 4low

Check the fuses of the lo and hi 4 wheel drive or disconnect the terminals put them together for ten minutes and reconnect and start and see what happens

Jan 21, 2012 | 2006 Hummer H3

1 Answer

Is there suppose to be any noise when engaging n disengaging 4LOW and 4HIGH?


Jan 20, 2011 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

F-250 will not go into 4-low, 4-high is ok

Good Evening. 4high is a simple deal to get working. 4low has a few more steps. First of course is starting the truck, shifting down into neutral at a stop then put it in 4low. After doing so then put it down in drive 4low should now be engaged. And to take it back out of 4low simply reverse the operation. Any other questions let me know, becuase if it can do 4high the shifting motor can do 4low.

Aug 11, 2010 | 2002 Ford F250 Super Duty SuperCab

2 Answers

My 1999 chevy z71 is stuck in 4Low and now none of the buttons light up? I can not get it back into 2 wheel drive or even 4high

the first thing is to check all your fuses, if fuses are good then you may have a bad switch or a bad selector motor,

Apr 21, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

95 chevy blazer 4low works..but when shifting into

My guess is that it is probably the actuator on the front diff. It may also be the buttons. I had the same problem with my 1999 silverado which it turned out to be the actuator.

Dec 14, 2009 | 1995 Chevrolet Blazer

1 Answer

Don't know how to put my 2002 sonoma p-up into 4 low

If you're going too fast, the 4low will not work, if you push 4high, it should do good for you. The 4lo is for creeping, and torque. The 4high works almost as good as AWD. Usually up to about 45-50mph. Hope that helps

Feb 14, 2009 | 2002 GMC Sonoma Extended Cab

1 Answer

4 wheel drive issues, appears to work in 4low but not 4 high

yes it is the switch. the switches are bad about going out in chevrolets which I am very familiar with. generally speaking if it goes into 4wd period it eliminates the actuator, and it also means t-case is functioning, it is just the selector switch.

Dec 19, 2008 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides