Question about 2006 Pontiac Montana SV6

1 Answer

Are the rear wipers and rear washers wired together? On a 2006 Pontiac Montana.. My wiper doesnt work but washer does..

Posted by on

  • princehouse Feb 07, 2010

    Fuse is good.. Checked power supply to the motor.. Have good power to motor.. So will replace with new motor. thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

I would check fuse, make sure it is good. I would pull panel and make sure you are getting 12 volts to motor, if you are it could be a bad motor, I would find out what one costs from your auto parts store, then call a reliable auto center, and get a repair quote from them, Please let me know what you find.

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

My windshield wipers on my 2000 Pontiac Montana won't stop as soon as I turn it on they start going I have tried turning it off of course but they just keep going


The switch is bad or the wiper motor cover ,electronics !
  1. Turn the ignition switch to RUN.
  2. Turn the wiper switch to OFF.
  3. Disconnect the wiper/washer switch connector C201.
Do the wipers park? yes or no ?
if yes Replace the wiper/washer switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle .
if no
Measure the voltage from connector C201 (vehicle side), terminal E2, to ground with a DMM.
Does the voltage measure greater than the specified value?
1.0 V yes or no ?
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
--
Go to Step 9
--

6

  1. Reconnect the wiper/washer switch connector C201.
  2. Disconnect the wiper motor connector.
  3. Measure the voltage from the wiper motor connector, terminal D, to ground with a digital voltmeter.
Does the voltage measure greater than the specified value?
1.0 V
Go to Step 8
Go to Step 7

7

Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
--
Go to Step 9
--

8

Repair the short to voltage in CKT 113. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 9
--

9

Operate the system in order to verify the repair.
Did you correct the condition?
--
System OK
Go to Wiper/Washer System Check



if yes

Apr 20, 2015 | 2000 Pontiac Montana

1 Answer

Rear wiper motor not working


Mr. Greequist,the first thing you have to check is the rear wiper fuse if is blown or not.

Sep 05, 2012 | 2006 Pontiac Montana SV6

1 Answer

Windshield washer does not work, Wipers work. Checked washer pump, it works. rear washer and wiper work fine.


so does it work or not? first you say it doesnt work, then you say it works? what car do you have? year? engine?

Aug 26, 2011 | Pontiac Vibe Cars & Trucks

2 Answers

I have a 06 montana the rear wiper not working but it only works when i push on the arm so i check and tight the arm but it till doing the samething what could it be


Wiper shaft is stuck by rust (aluminium oxide). Remove wiper motor. Knock out wiper shaft with soft hammer. Clean shaft hole with similar size drill bit.

Mar 14, 2010 | 2006 Pontiac Montana SV6

2 Answers

2006 pontiac montana i cant stop wiper blades mid stroke to change them cant reach them when they return to down in hood again


when running the wipers turn the key off upon were you want the wiper to be positioned at for your work

Jan 01, 2010 | 2006 Pontiac Montana SV6

2 Answers

2001 pontiac montana


Check the wire connection just below the wiper motor. Its located on the passenger side by the washer fuild tank cap. With the wiper switch on delay, try moving the connection back and forth. Keep your hands clear of the motor arm. You may have to secure it in the right postion with a zip-tie.

Apr 18, 2009 | 2001 Pontiac Montana

2 Answers

How do I install a rear wiper motor on 2003 Pontiac Montana?


Here's a great video that will show you how to install the rear wiper motor on a 97-05 Montana or Venture">

Feb 28, 2009 | 2003 Pontiac Montana

1 Answer

How to replace rear wiper blade in pontiac transport montana 1998


When you purchase a wiper blade, the step-by-step instructions are included in the package. It will be a matter of carefully pulling up and out, then reverse the steps to install.

Jan 20, 2009 | 2006 Pontiac Montana SV6

Not finding what you are looking for?
2006 Pontiac Montana SV6 Logo

615 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...