Question about 2005 Nissan Altima

1 Answer

I need to replace the passenger side low beam headlamp. It looks like a major task to get to.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

Remove coolant reservoir and washer fill tube. Turn and pull tube to remove. This will give access to headlight bulbs.

Posted on Feb 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

1986 dodge w150(power ram) headlight stuck on high beams. Also having trouble with passenger headlight not working. Already replaced Hi/Low dimmer switch.


Have you checked the relay in the circuit. You really need a schematic of the wiring diagram. Electrical can be tricky without the wiring diagram.

Jul 22, 2017 | Dodge Cars & Trucks

1 Answer

Right low beam headlight does not come on but my right turn signal will stay even tho i diddnt turn it on. If I cut on my high beams the rurn signal cuts off. Whats wrong? Helo


It could be the lamp control module !
Headlamps
Battery positive voltage (B+) is applied at all times to the lamp control module (LCM) through the underhood fuse block HDLP fuse.
When you place the headlamp switch in the HEAD position, the headlamps input to the LCM is grounded. The LCM then applies battery positive voltage (B+) through the underhood fuse block HDLOBML fuse and HDLOBMR fuse, which feed the left low beam headlamp and the right low beam headlamp respectively. When you activate the headlamp dimmer switch by pulling on the multifunction lever until the switch clicks, the high beam input circuit to the LCM in grounded . The LCM then removes battery positive voltage (B+) from the low beam headlamps and supplies battery positive voltage (B+) through the underhood fuse block HDHIBML fuse and HDHIBMR fuse, which feed the left high beam headlamp and the right high beam headlamp respectively.
Check this fuse in the left under hood fuse box first. HDLOBMR Fuse 18 10 Amp. RH Low Beam Headlamp . If the fuse is good check for B+ voltage with the low beams on . Use a test light or volt meter . If you look on top of fuse there are two metal tabs ,check there for B+ voltage , If no B+ voltage the LCM - lamp control module isn't supplying any .
Lamp Control Module (LCM)
Under the left side of the IP, to the right of the steering column
Turn Signal Flasher
Under the left side of the IP, to the right of the steering column
Lighting Systems Component Views in Lighting Systems
Lighting Systems Connector End Views in Lighting Systems
Turn Signal/Hazard Switch
In the left front of the passenger compartment, in the steering column

Apr 28, 2016 | 2000 Buick Park Avenue

1 Answer

2002 Cadillac Deville - my driver side headlamps seem to give off only a low amount of light while the passenger side shines as normal on both low and high beams. I replaced the bulbs but that didn


Are you sure you replaced the bulbs with the same brand/model as on the passenger side? There are a lot of different versions with different light colors and intensities.
If so, have you made sure there is no water vapor in the headlight housing, and that the silvering inside is not degraded?

Oct 07, 2017 | 2002 Cadillac Deville

3 Answers

I have a 2006 ford escape and the passenger head light low beam will not work. Tried replacing the bulb, and check fuses nothing is working.. what else can I try?


Both your low beam and your high beam is protected by the same fuse, so it makes sense that the fuse is OK if the high beam is working on the passenger side. There are 3 fuses for the headlamps. Fuse #13 in the Battery Junction Box (20 Amp). If this fuse is blown, the headlamp relay will not have any power and neither high nor low beam on either side will work (you will have no headlamps at all) Then there is Fuses #2 and #3 (15 Amp) in the Battery Junction Box. #2 goes to the left low and high beam and #3 goes to the right low and high beam.
The headlamp switch uses a SINGLE CIRCUIT to control BOTH sides at the same time, so if one side works, the switch cannot be the problem. The headlamp relay provides power for fuses #2 and #3 and we already ascertained that these fuses must have power since we have working lights on both sides, so the relay cannot be the problem. A replacement bulb has already been tried, so that pretty much leaves us with a bad lamp socket. (Most likely cause) or a bad connection at splice #S122, which is located in the main wiring harness near the breakout for the left headlamp. (RED/BLACK wire)

May 16, 2011 | 2003 Ford Escape

2 Answers

Audi A4 2002 Low beams & Right front turn signal stopped working


For Audi A4 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.
First fuse on first row from left upper corner is Fuse Nr.20 = F20 (15A) - RH headlamp low beam, headlamp adjustment.
First fuse on second row from left upper corner is Fuse Nr.21 = F21 (15A) - LH headlamp low beam, headlamp adjustment.

Feb 15, 2010 | 2002 Audi A4

1 Answer

Passenger headlight don't work 2003 lincoln navagator


high beam or low beam? or both of them on one side.

  • One low beam headlamp is inoperative
  • Central junction box (CJB) fuse 23 (10A) (RH headlamp).
  • CJB fuse 25 (10A) (LH headlamp).
  • Circuitry.
  • CJB.
  • Go To Pinpoint Test C .


  • One high beam headlamp is inoperative
  • Circuitry.
  • Headlamp assembly.
  • Go To Pinpoint Test D .

  • The high and low beam headlamp is inoperative on one side
  • Circuitry.
  • REPAIR ground circuit 57 (BK).


  • Headlamp switch
  • Multifunction switch
  • Vehicle Security Module
  • Central junction box (CJB) fuse(s):
    • 17 (15A)
    • 23 (10A)
    • 25 (10A)
    • 35 (20A)
    • 40 (20A)
  • Circuitry
  • Headlamp bulbs
  • Daytime running lamp (DRL) relay



Apr 19, 2009 | 2003 Lincoln Navigator

1 Answer

Replace low beam headlamp, passenger side, 2004 Navigator


Remove the front radiator air deflector.
Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
ef5d2b9.jpg
Remove the headlamp bulb protective cover.
1 Low beam cover. 2 High beam cover.

babb381.jpg
b8093f8.jpg

Feb 13, 2009 | 2003 Lincoln Navigator

2 Answers

Right headlamp


Check the fuse for the passenger side.It is under the hood. it may not be making good contact. wiggle it a little bit and see if it makes any difference. if not, check where the the ground wires are connected to the chasis. See if thats not the problem.

Oct 31, 2008 | 2001 Buick LeSabre

Not finding what you are looking for?
2005 Nissan Altima Logo

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...