Question about 1991 Cadillac Seville

1 Answer

Key won't engage,Power all a go when key is accepted...

This hasbeen going on for months but today I could not get the ignition to accept the key... Jeep Cherokee 2001

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 105 Answers

Hello, make sure the gear shift is pushed all the way in park, you can also grab towards the bottom of steering wheele, and try to twist it to the left, to put in park, you may need to have someone adjust your linkage on transmission,

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Stick my key in the ignition to start a saubb 9.5 and it tells me key not accepted what is the problem need help fast???


You can start your vehicle, just turn key to start. hit any button on remote, if it accepts the signal. Then car will start. You can also go to dealer to have the system checked, and find out whats wrong. Because there are many reasons why this has happened. Hope this helps!

Aug 13, 2014 | Cars & Trucks

2 Answers

I have a 92 Oldsmobile Toronado that was recently broken into and my igniton was broke. And now I can't start it. I can put the key in it and turn like usual but the information center is saying starting...


I believe that your key has a resistor chip. You will need to find the resistance of your chip. Once found, go to an electronics store and buy a resistor with the same value. Follow the two wires that go from the ign switch down the steering column , into a 2 wire plug into the ign module. Unplug the connector. Plug the resistor to the module. The module will read this value and allow you to start the car.

Nov 24, 2013 | Cars & Trucks

1 Answer

2006 Kia Rio key won't accept code


So your saying a dealer can not fix their own products

That's their problem,now your car is there

Have at least 3 working keys for all your vehicles

Jan 21, 2013 | 2006 Kia Rio

1 Answer

My next question is if the original key wont start the car how do i get a vats key


you measure the ohms on the resister in the key using a digital multimeter. once you get the value you go to the dealer and ask for the number key that matches the resistance, get the key cut.

1 0.402 (acceptable range .386-.438)
2 0.523 (acceptable range .502-.564)
3 0.681 (acceptable range .650-.728)
4 0.887(acceptable range .850-.942)
5 1.130 (acceptable range 1.085-1.195)
6 1.470(acceptable range 1.411-1.549)
7 1.870(acceptable range 1.795-1.965)
8 2.370(acceptable range 2.275-2.485)
9 3.010 (acceptable range 2.890-3.150)
10 3.740(acceptable range 3.590-3.910)
11 4.750(acceptable range 4.560-4.960)
12 6.040(acceptable range 5.798-6.302)
13 7.500(acceptable range 7.200-7.820)
14 9.530(acceptable range 9.149-9.931)
15 11.801 (acceptable range 11.320-12.290)

Oct 09, 2012 | 1998 Cadillac Eldorado

1 Answer

07 Navigator pulling codep-1260,How to clear without going to dealer


P1260 that is anti theft code, The definition is Theft detected,vehicle immobilized, Your going to have to bring in a mobil locksmith in and have immobilizer reset. Or try this put the key in the ignition and turn it to the ACC 3 times fast and leave the key in for at least 10 minutes. Then try to start the vehicle because there is a possibility the ant theft will accept the keys agian. by the way youll always have this problem it always fails to accepts its own keys

Apr 23, 2011 | 2007 Lincoln Navigator Ultimate 4x4

1 Answer

I have a 1995 camaro. it will not start. i ran a jumper wire to the solenoid and turned the key on. it starts but will only run for about 5 seconds? it has a new ignition with security key


Did the dealer install the new ignition?. If so, then he would also have to replace the sensor that goes with it which is attached to the steering column, Then he would have to reprogram the on-board computer to accept the new security code. Just changing the ignition and key won;t work. Check out this website for more informaiton: http://newrockies.ca/vatsbypass.

Dec 28, 2010 | Chevrolet Camaro Cars & Trucks

1 Answer

2005 jetta ignition won't accept key. how to release transmision for towing


TRY ANOTHER KEY.STILL WONT ACCEPT KEY.YOU HAVE KEY IGNITION SWITCH TO IMMOBILIZER FAULT.YOU NEED A VOLKSWAGON MECHANIC TO BRING SCAN TOOL TO TRY FIX OR REPROGRAM KEY AND IMMOBILIZER SO CAR CAN BE TOWED THIS IS THE ONLY WAY WITH OUT DAMAGING ANYTHING.

Sep 01, 2010 | 2005 Volkswagen Jetta

1 Answer

My 2002 sabb 95 dash said the ignition key was not accepted and wont start


It sounds like you have a problem with your twice module (theft warning integrated central electronics). It energizes a loop of wire surrounding the key and sends the power to the transponder sends a code around the same loop and sends it to the module which checks to see if it is an accepted key.....obviously you have a problem somewhere in that circuit. I hope this helps. Good luck!

Apr 23, 2010 | 1999 Saab 9-5

1 Answer

Key won't come out of the ignition


That's a commom problem with VW's. Restart engine. turn steering wheel hard left and switch off.

Jun 14, 2009 | 2004 Volkswagen Jetta

1 Answer

Ignition won;t start. The key insert is loose and turns but won't start


the ignition switch may need to be replaced. im not sure if a lock smith can replace the ignition switch, call around to see if they can.

May 29, 2009 | 2000 Lexus LX470

Not finding what you are looking for?
1991 Cadillac Seville Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...