Question about 2002 Dodge Grand Caravan

1 Answer

How do you aim the headlights on 02 caravan? - 2002 Dodge Grand Caravan

Posted by on

  • Dale Schultz Feb 08, 2010

    Thanks.I was looking in the wrong spot.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Headlight adjustment. adjustment screws face forward above and to the left of the lens. On the front of the van in the gap between the trim. There are 2 adjustment screws on each side one on the top one on the outside area. You should park in front of a wall.park about 100 feet and align the lights so they point directly ahead of the vehicle and are level with it. If the light needs to go up tighten the top screw, if it has to go down loosen it. You may need to use some pressure with your hand when loosening it. If it has to go inward you would loosen the outside screws if it has to go the other way tighten it. hope this helps, have a nice day

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How remove head light assembly


Mine is a little earlier, but open the hood, on top of headlight there is a black tab on top fastening it to the frame, remove it. Then look behind the headlight, surrounding the area, where the headlight wires connect to the bulb, there are 3 hex nuts, remove them (carefully, as if you drop them, they will probably fall into the "Bermuda Triangle" never to be seen again. Headlight and turn signal/ parking light assembly SHOULD slide out the front, if it still won't move, check for another hex nut/bolt or phillips screw holding it in. DO NOT turn the two adjusting screws, visible from the top Deep inside holes on the top, as this will do no good getting the light assembly out and just mess with the aiming of the headlight. Hope this helps.

Feb 11, 2015 | 2008 Dodge Grand Caravan

1 Answer

How do you aim or adjust 200l legacy headlights


Hello Terry.

HEADLIGHT AIMING



CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than two minutes .
NOTE:
Before checking the headlight aiming, be sure of the following:
  • The area around the headlight has not sustained any accident, damage or other type of deformation.
  • Vehicle is parked on level ground.
  • The inflation pressure of tires is correct.
  • Vehicle's gas tank is fully charged.
  • Bounce the vehicle several times to normalize the suspension.
  • Make certain that someone is seated in the driver's seat.
  1. Place a cloth over the headlight that does not require aiming adjustment.
  2. Turn the headlights on. Perform the aiming adjustment for the other headlight as follows:
kiltylake_66.gif

CAUTION: Do not perform lateral headlight aiming adjustment.There you are, the procedure from Subaru manual.

Hope this helps you.
Thank you for using FixYa.

KL

Dec 04, 2010 | 2001 Subaru Legacy

1 Answer

Can't find the adjustment screws for the headlights on a 2008 Tundra


Adjust the vertical headlight aim into the specified range by turning aiming screw A with a screwdriver.
  • Perform lo beam aim adjustment.
  • The headlight aim moves down when turning the aiming screw clockwise, and moves up when turning the aiming screw counterclockwise.
  • 5687808.jpg

Oct 16, 2010 | 2008 Toyota Tundra

1 Answer

Can't locate the headlight adjusment screws on 1999 grand voyager


The headlights are equipped with adjusters and a built in level to aid in proper aiming



649f32f.gif

Apr 23, 2010 | 2000 Dodge Grand Caravan

1 Answer

Chrysler town country 1996 headlight adjustment.how do i do that.they are to low and to high


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 29, 2009 | 1999 Dodge Caravan

1 Answer

How do I adjust the headlights on a 04 caravan


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 08, 2009 | 2004 Dodge Grand Caravan

2 Answers

How to adjust headlights on 2005 dodge grand caravan


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Sep 17, 2009 | 2005 Dodge Grand Caravan

1 Answer

02 Dodge Caravan one headlight will only work at


i have seen this problem before..sounds like underhood fuseblock is bad..flip unit over and check connections..dealer part..hard to get at a wrecker's here..may not be where your located..

Apr 09, 2009 | 2002 Dodge Caravan

1 Answer

Adjustment headlights '02 Hyundai Elantra


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jan 23, 2009 | Hyundai Motor 2002 Elantra

1 Answer

02 dodge caravan headlights


SOUNDS LIKE INTEGRATED POWER MODULE(UNDERHOOD FUSEBLOCK)IS DEFECTIVE..ALSO CHECK FOR CORRODED TERMINALS IN CONNECTORS ON FUSEBLOCK..HAVE SEEN THIS BEFORE AND NEW FUSEBLOCK WAS NEEDED AND REPAIRED PROBLEM

Jan 06, 2009 | 2002 Dodge Caravan

Not finding what you are looking for?
2002 Dodge Grand Caravan Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...