Question about 2006 Pontiac Montana

Open Question

How to change 2007 montana front signal bulb - 2006 Pontiac Montana

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Left front turn signal bulb for 2001 Pontiac Montana

There is only one screw to remove that releases the mounting tab at the upper inner corner of the assembly. That screw has a plastic wingnut molded onto it so you can turn by hand. Once that is removed, the assembly can be pulled straight forward. At the inner bottom corner, a spring clip faces straight rearward. Pull with enough force to to release the clip from its slot. Only two "Fingers" hold the rear of the assembly in the sheet metal holes.

Posted on Nov 15, 2008

Ad
  • 1 Answer

SOURCE: real right turn signal light - Pontiac Montana SV6 2005

If the 2005 Montana is similar to the 2001 Montana, I have a solution. First you'll need a hexagonal wrench (the 6-sided L-shaped wrench). The tail light assembly is held on by two screws. You'll need the hexagonal wrench to remove them, because a normal screwdriver won't do it. I also had to use a conventional adjustable wrench to get the leverage to turn the hexagonal wrench, because the screws were in there pretty tight. Once you remove the two screws, the whole tail light assembly should come off. Mine required a little force and I had to play with it a bit, but it came off without a lot of work. There will be one set of wires that connects the tail light assembly to the rest of the minivan--try not to damage that set of wires. Once you get the tail light assembly off, you'll have to take apart the assembly that actually holds the lights. No tools should be required. It's held on by four plastic catches. Just undo the catches (easier said than done, but still not too tough) and it comes apart. Then you can pop out the old light and pop in the new light. Then re-assemble. For me, it went back together much easier than it came apart.

Posted on Jan 03, 2009

  • 840 Answers

SOURCE: How do you access the

if their is a engine cover take cover off / their are 2 bolts for the headlight take them out and pull the headlight forward

Posted on Jan 25, 2009

  • 36 Answers

SOURCE: How do you change the 2007 Jeep Patriot turn

You might have to remove the headlamp assy to get to it.

Posted on Jul 07, 2009

  • 120 Answers

SOURCE: 2007 ford 500 rear turn signal bulb replacement

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Posted on Jan 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left front turn signal was not working, and i replaced it with a new bulb but it did'nt work...please help .. ty


try changing the signal flasher. note the e-flasher looks the same. when you find a flasher turn on the e-flasher so you know you have found the signal flasher. they are usually in the same general area.

Aug 12, 2015 | 2006 Pontiac Montana SV6

1 Answer

How to change 2007rear left signal on 2007 mantana v6


If the light has no screws holding it in outside, you can gain access to the bulbs from in the trunk under the carpet in the back.

Nov 29, 2014 | 2007 Pontiac Montana

1 Answer

Changing the rear turn signal bulb


Some bulbs are really tough to remove on this car. Specially the front side lights. You have to first remove the panel in front of the tires. Hope this helps.

Apr 04, 2014 | 2007 Chevrolet HHR Fall

1 Answer

How do you get access to change the front right turn signal bulb on a 2005 pontiac montana SV6?


Open the hood. If you cannot gain access, the grill of the vehical will have to be removed. This will give you access to the bulb.

Apr 17, 2011 | 2005 Pontiac Montana SV6

1 Answer

I want to know how to change the bulb in my headlight of my 2005 pontiac montana?


1. Open the hood.

2. Remove the front turn signal/parking lamp
assembly. See Front Turn Signal, Sidemarker and
Parking Lamps on page 5-46.

3. Pull the assembly away from the vehicle.

4. Unscrew the black retainer ring that holds the bulb
assembly in place.

5. Pull the bulb assembly straight up from the
lamp housing.

6. Unhook the electrical connector by lifting up the
blue tabs and pulling the bulb out.

7. Install the new bulb through the black retainer ring
and into the electrical connector.

8. Tighten the black retainer ring in place. Push the
bulb firmly enough so that the blue tabs hook over
the tab on the bulb.

9. Carefully put the bulb assembly back into the lamp
housing. Be careful not to damage the bulb on the
headlamp aiming bar.


Same guide is here in the manual along with pictures.

http://www.extendedgmwarranty.com/owners-manual/pontiac/2005-Pontiac-Montana.pdf

On page 370

Mar 02, 2011 | Pontiac Montana Cars & Trucks

1 Answer

Replace front right turn signal bulb


I replaced the front right turn signal on my 2005 Pontiac Montana by reaching up from underneath. I tried removing the battery but the opening from above was too small. I was able to pull the ground effects open enough to get my arm in. When you reach the bulb holder feel for two wings on the bulb socket and give the whole socket a quarter turn to and it will release. The wires are long enough so the entire bulb holder will drop down below the vehicle so you can easily replace the bulb.
Reverse the step to put it back in. You will not be able to see what you are doing so I had someone guide me by watching from above. Took less than 10 minutes once I decided to change the bulb from the bottom. I did not need to jack the vehicle up or use ramps.

Jun 14, 2010 | 2005 Pontiac Montana SV6

1 Answer

2000 pontiac montana. I want to replace the driving ligh bulbs. the under the headlights what size is it?


Fog/Driving Light Bulb Size: 880
Here is the rest of the bulb size used in your Montana.
2000 Pontiac Montana Auto Light Bulb Diagram
Low Beam Headlight Bulb Size: 9004
High Beam Headlamp Light Bulb Size: 9004
Parking Light Bulb Size: 4157NALL
Front Turn Signal Light Bulb Size: 4157NALL
Rear Turn Signal Light Bulb Size: 3156
Tail Light Bulb Size: 3057
Stop Light Bulb Size: 3057
High Mount Stop Light Bulb Size: Assembly
Fog/Driving Light Bulb Size: 880
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3156
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 558
Glove Box Light Bulb Size: 194
Map Light Bulb Size: 168
Dome Light Bulb Size: 562
Step/Courtesy Light Bulb Size: 168
Trunk/Cargo Area Light Bulb Size: 212-2
Daytime Running Light Bulb Size: 3157NALL
Thank you for using fixya.


Apr 30, 2010 | 2000 Pontiac Montana

1 Answer

1998 pontiac transport/montana has not tail or break lights...turn signals blink fast or not at all. changed rear bulbs and noticed carbon on front build up on front bulbs. Help!


If one of the filaments in the bulbs is burned out, the remaining working lights will flash alot quicker.
Check the bulbs, and replace if the filaments are broken.
If the front bulb has a carbon build up it blown out...change it..
Once the bulbs are replaced your signals should work properly.

Dec 09, 2009 | Pontiac Trans Sport Cars & Trucks

3 Answers

Right turn signal flashes fast. Front bulb appears to be burned


There are 2 bolts on the top corners of the bulb lens that needs to be removed then the lens pops right out and you can change the bulb.

Apr 06, 2009 | 2006 Pontiac Montana

2 Answers

The front right blinker is out and I am not sure what kind of bulb I need and I don't know how to get it out without messing with the headlights, which I don't want to do.


Your local auto parts store will have the listing for the bulb you need. (should only be a couple of bucks).
And depending on the parts store, they might even put it in for you if you ask.
It's a fairly simple job to do.
Take the bulb out of the assenbly (from the back) take the bulb out of the socket, put the new one in, plug it back into the assembly.

Jul 29, 2008 | 2007 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

794 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...