Question about 2001 Honda CR-V

Open Question

Crv drive cycle. how long and what speed to reset?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A mechanic reset my computer on my 02 Taurus. I need to get it to cycle so I can pass inspection. How do I need to drive it to cycle fast?


With a scanner attached to it. Takes about an hour of driving. the scanner tells you the driving speed and time. There will be highway driving at different speeds, then driving in stop and go traffic.

May 30, 2016 | Cars & Trucks

1 Answer

The owners manual says to inspect idle speed at 160,000 mi, how is it done 2003 Honda CRV


Are you having an idle issue ??
Vehicle equipped w/Tachometer ??
Cold engine idle speed ??
Warm engine idle speed ??
Warm engine idle speed @ A/C requested on ??

May 28, 2015 | 2003 Honda CR-V

1 Answer

Car wont go 50 mph


Maybe the exhaust converter is blocked

Aug 26, 2013 | Honda CR-V Cars & Trucks

1 Answer

Crv vibrates for a few seconds as if going over rumble strips 2004


Check cv joints and check loose bush in diff casewhere the shaft goes in. Try lifting up and down as I think you have a problem with the drive shafts binding up

Feb 11, 2013 | Honda CR-V Cars & Trucks

1 Answer

Crv 2006 vibrates at any speed. slow down or speed up it goes away. your thoughts


i have honda crv 1999 it never speed up to 120km/h when it 120km/h sometime i feel shakeany help

May 06, 2012 | 2009 Honda CR-V

1 Answer

HOW MANY MILES DOES IT TAKE TO RESET MY GMC ENVOY 2003


It's not a matter of miles, but the number of drive cycles. Each drive cycle includes low and high speed driving, and I think there are 10 drive cycles required.

Aug 11, 2011 | 2003 GMC Envoy

1 Answer

Vibrating on the passenger side at low speed fory honda 2003 crv


the most common reason for a vibration is most of the time due to a bad tire. check the tire and look for a bubble or what we call a hop in the tire, this is on the tread of the tire not the sidewall. a good way to do this would be on a lift, this will be hard for you unless you spot the bad tire otherwise the crv will need to be put on a lift and ran in drive as you watch the tires spin and look for a hop in the tire, your crv is 4wheel drive which means all wheeels spin so all tire must be off the ground when checking them. if the vibration is at low speed then the bad tire should be easy to find, this is where i would start first, with tire checking, alsomake sure tire pressure are correct, at around 32psi. good day.

Apr 10, 2011 | Honda CR-V Cars & Trucks

1 Answer

Gas cap indicator light stuck on; gas cap is on-checked it ten times. 2007 Nitro, about 40,000 miles


Hello,
There are a number of things that the computer system will reset automaticly, but, it usually requires 2 drive cycles.

A drive cycle includes, accelerating, highway speed, local speed, stopping. If you have already done that, you may try to reset by removing the ground cable, ( black wire ), from the battery for a minute or so.

I hope this helps you.

Feb 16, 2011 | 2007 Dodge Nitro R/T New Cars

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

1 Answer

Need to do a drive cycle?????


a drive cycle is very complicated and is outlined in the factory emission manual, but here is the short version, u need to do about 20 miles of mixed driving, freeway steady speed, then stop and go and steady low speed, repeated idle times and stop and go, so just drive it in town and on the freeway for a few days and I am sure it will clear the drive cycle test and be ready to pass emission test.

Apr 11, 2009 | 2004 Dodge Caravan

Not finding what you are looking for?
2001 Honda CR-V Logo

Related Topics:

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...