Question about 2001 Isuzu Trooper

1 Answer

I am changing the cv boot on the car I have got isuzu trooper 03

I am changing the cv boot on the car I have got the track rod end is off,undone the bolts to top and bottom ball joint, removed brake caliper but cant seem to get the hub to come off the drive shaft moves about 2 inches but will not come out off hub and I cannot release hub for some reason how do I release it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Undo the ring of allen head bolts in the middle of the wheel,then undo the 3 X head screws on the wheelbearing adjuster ,spin that off and the hub will pull off the shaft with the bearings .

Put fresh grease in the bearings on rebuild and adjust the bearings as per the manual - its a preload figure .

Posted on Feb 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Howdy, 94 Isuzu bighorn diesel. Need to replace front cv boot. Have stripped it all down so the cv joint is exposed and lose but still attached to the shaft. Have cut away old boot to look at what is...


if you are trying to reassemble the cv joint ( why ever you would need to pull it apart in the first place as the new boot slips over the assembly)
do it outside of the transmission or you will damage the transmission internals
place the transmission end on a block of wood
line up the shaft and hit the top end with a heavy mallet
( sledge hammer will burr the ends )
of you are just putting the shaft back in the transmission to reassemble the front end , line up the splines and use the mallet to start the splines into place by compressing the circlip

May 06, 2017 | 1994 Isuzu Trooper

1 Answer

I can hear an intermittent (grind then no grind) noise, the frequency of which increases when the speed of the vehicle increases. It sounds as if it is coming from the rear wheel. Im in an 1997 Isuzu...


Not the CV joint, I don't think you have one in the rear, but the wheel bearing, yes, Next time you drive it, crawl under there and feel the rear end next to the wheel, Careful, Hot? How about closer to the wheel, then how about the drum dust cover itself? If it hotter than it should be, like oil boiling out or brake fluid boiling out, time to change the bearing, don't wait for it to seize on the axle, you will have to cut it off. You will need to check the book on the way the axle comes out, some come right out, some are attached inside the rear end, need to be un-clipped, then the axle will come out, You will need a slide hammer or a chain to snatch it out of there. Good luck, hope this helps.

Jul 04, 2010 | 1997 Isuzu Trooper

1 Answer

CV axle removal 1999 Isuzu Trooper


The easy way is to take the inner boot off and take the joint apart. Take new cv axle apart at inner joint and attach to the old one sticking out of axle housing. You will need to get new boot clamp.

Mar 03, 2010 | 2003 Lincoln Town Car

1 Answer

'93 Isuzu Rodeo, CV Joint replacement.


unbolt the tie rod end and the lower a arm and it should slide out of there

Jan 26, 2010 | 1999 Isuzu Rodeo

1 Answer

Front drive shaft removal for 2001 izuzu trooper 4x4


Under the rubber boot inside the CV joint is a big spring clip round the edge , take this out and then the shaft pulls away from the axle with the CV on it .If you are fitting a new boot cut the old off if not just get the clips off and pull the boot back.

Did you take the shaft out from the wheel hub end too ?

Oct 04, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

Change a cv boot on a 1996 isuzu trooper


First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Sep 28, 2009 | 1994 Isuzu Trooper

2 Answers

How do i remove cv axle for a 98 isuzu trooper


Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Sep 27, 2009 | 1998 Isuzu Trooper

1 Answer

Removing half shaft from 2000 isuzu trooper


must remove clips from inside front axle housing!! If the cv joint aint broke DONT FIX IT the boots can be replaced in less than 1 hour with hand tools and the boot is around 20$ at any parts store

Mar 31, 2009 | 2000 Isuzu Trooper

Not finding what you are looking for?
2001 Isuzu Trooper Logo

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...