Question about 2000 Mercury Mystique

1 Answer

Do I need a special key when I have a replacement key made

Posted by on

  • dlmkam Feb 06, 2010

    I already knew that,No manual, I had a cheap key made & didn't know if it was the key maker or needed a special key.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Mercury Master
  • 752 Answers

Alot of newercars have immobilizer chips in keys for theft check ur manual or have a cheap key done just in case you ever lock ur keys in car and test the new key and see if it stars ur car

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the ignition switch. Key in place, will not turn back to the off positiom, stuck in run. 1993 Chev Silvarado


It is held in with a bolt. You need to remove the steering wheel, lock plate, and turn signal switch to gain access. You will need special puller for the steering wheel and a special tool for removing the lock plate.

Jun 02, 2011 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

How do i fix the problem with the key lock spinning around the car wont start


This a safety feature in the BMW if the ignition is forced it breaks
need to replace the ignition cylinder

Removing and installing/replacing lock cylinder for steering wheel lock

Car with ring antenna:
Remove lower section of steering column trim.
Using special tool 61 3 300, press ring antenna off locking cylinder.

83357444

With ignition key, use workshop key for better accessibility, turn lock cylinder to "R" position = radio, windscreen wiper, fan.

Caution: On vehicles with freewheel lock cylinder up to 10/95: twist lock cylinder back through 12°.

83357445

Push special tool 32 3 110 into hole of lock cylinder an swivel handle forward by approx. 90°. Remove lock cylinder.



You can substitue a pick for the tool

Jan 01, 2011 | 1997 BMW 328

1 Answer

Key switch replacement


Go the the library and read the Chilton;s manual for replacing the ignition Key Lock Cylinder. It will show you what special tools that are needed with pictures as well
It is a long process to change and can not take the time to write 4 pages of instructions to you
copies of the pages from the book can be made there as well

Jun 08, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Key will not go into ignition switch,need to know


yes a lock plate compressor for the steering lock

Mar 12, 2010 | 1997 Chevrolet Lumina

1 Answer

Need key replacement


These cars have a security system that requires a special key. Talk to your local Buick/GM dealer. You will need the VIN and some other numbers that can be found on the drivers side door.

Good Luck!

Feb 14, 2010 | 1992 Buick LeSabre

1 Answer

Do i need a special key or can i go to a regular locksmith


You do need a special key as Nissan uses what is called a transponder key. I believe a regular locksmith with auto key capability can sell and program a key for you. Call before you run down there to make sure.

Oct 12, 2009 | 2006 Nissan Pathfinder

1 Answer

Key Cylinder needs replacing


you must remove the air bag,steering wheel, directional switch and lock plate. There is a screw which locks in the lock cylinder but unfortanetley it is not easily accessable and there is a special tool needed to remove the lock plate snap ring

May 26, 2009 | 1998 GMC Sierra

1 Answer

Replacing brakes, 03 mini


there is nothing special about replacing the wear sensors. The tools that you will need are 7mm allen, 16mm 6 point socket, ratchet, T-50, large channel locks, and a keyed pad pusher for the rear calipers.

Apr 01, 2009 | 2003 Mini Cooper

1 Answer

Replace front brake pads on 2000 expedition


just a toex head tool for the caliper pins

Jan 29, 2009 | 2004 Ford Expedition

Not finding what you are looking for?
2000 Mercury Mystique Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...