Question about 2000 GMC Jimmy

1 Answer

2000 jimmy has no indicator lights on dash for 4x4 system they use to all come on when key was first turned on to show they all worked now they dont even do that and will not go into 4 wheel mode. all fuses check out o.k. please help snows on the way

Posted by on

  • jpcgolf66 Feb 08, 2010

    this did not work and the tccm only has one plug going to it not 2


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,111 Answers

I believe its fuse #19 or 21 for the 4wd but may be under the interior or accessory lights i would check all the fuses 1st with a test light to ensure both ends are getting power and that they are properly seated into position then ...start tracing for power to the switch itself it merely pops out from either side with a small Flathead screwdriver and check for power there as well they are just wires and indicate the bulbs may have burned out indicating also a bad switch but check for power 1st and proper seating of the fuses

if 4 wd is not present it could be either vacuum or cable from under the battery tray or the encoder motor or the wires to the sensor have come rusted or ? corroded broken etc somehow and a visual inspection is necessary to determine the exact cause look up on top of the front drivers side axle housing for open wires etc check all the wires and especially the vacuum lines for wear /// cracks / dryrot / missing or disconnected to begin

Posted on Feb 06, 2010

  • Duane Morse
    Duane Morse Feb 08, 2010

    try disconnecting the fuse for the 4wd for a few minutes this sometimes will fix minor issues related

    also on the passengers side kick-panel there is a box behind it remove the kick panel to see if the wires are not corroded and rusty as they are known for water getting in and causing problems .

  • Duane Morse
    Duane Morse Feb 10, 2010



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2000 gmc 1500 z71 and my 4x4 indicators cuts in and out and so do my turn signals they just stop working then will start working again worse on rainy days and ideas

Sounds like you have a lose ground , both turn/ hazards an 4X4 switch share Ground G203 .
On the left upper IP at the A pillar
(1) Splice Pack 203 (SP203) (2) Ground 203 (G203) (3) Dash (4) A-Pillar
You will need to take parts of your instrument panel apart to get at it.

Feb 02, 2016 | GMC Cars & Trucks

1 Answer

No lights for transfer case on 1985 gmc jimmy, 4x4 not operating no indicator light to show position,

if you have no lights that's one thing , but if 4x4 wont ingage that tells me it may be a fuse and if the 4x4 wont ingage it wont light the icon on dash

Feb 26, 2015 | GMC Cars & Trucks

1 Answer

Car fuse keeps blowing

check underneath around the gearbox or front and back diff for any damaged wires that may be rubbing against the body or metal components there is a short

Jan 16, 2014 | 2000 GMC Jimmy

1 Answer

I have a 98 gmc jimmy the 4x4 is not working it has the push button on the dash and when you put it in 4x4 the lights work but it dont go into 4x4

Sounds like the transfer case motor is going out or bad, i know the trucks have a 4x4 engagement motor on the front differential which engages the front axles. i am not sure how yours is setup, you will have one or the other.

Dec 18, 2013 | GMC Jimmy Cars & Trucks

2 Answers

My jimmy starts and runs when it wants to then sercruity light comes on and shuts it off

Yes the truck came with a stock antitheft system. That IS what the security light is about. Check out this link. Everything you need to know is there.

Apr 24, 2011 | 2000 GMC Jimmy

1 Answer

2000 Jimmy - starts but can't shift into gear - can't push button in

Check ALL the fuses !!! Does the brake lights work? if not,, the shift inter lock may be disabled ,,, if the lights work the interlock solenoid might be the culprit . You should be able to get in gear by turning the ignition switch off then turning to the first selection ,,don't turn it untill the dash lights come on ,,with the key in that position you should be able to shift the lever to put it in gear ,,,,dont move the key untill its in the correct gear

Mar 15, 2011 | GMC Jimmy Cars & Trucks

1 Answer

Does my 2000 jimmy SLE have a seat belt chime! dont know as i dont have the manual! and i just have a light on the dash and if so where is the chime located? thanks dont need a ticket for no belt!!

Yes it should be under the left side of the dash above where your left foot would be. If you hear a bell when the key is in the switch with the door open, then the wire for the seatbelt may be cut.

Jan 09, 2011 | 2000 GMC Jimmy

1 Answer

ABS Problem in my 2000 Jimmy 4x4

the best way to diagnose this problem would be with a scan tool while driving and watching the speed sensors, or check all your wheel tone rings make sure there are no cracks and they are clean, also have the computer scaned for abs codes there should be a code that may tell you which wheel speed sensor is acting up,you can also check the wiring, these seem to chaf the wiring by the control arm .a bad wheel bearing may also cause this problem, i would start with a scan of the abs system,good luck.

Feb 22, 2010 | 2000 GMC Jimmy

1 Answer

No power to dash 4x4 indicator lights all fuses are good

  • for the lights check the fuse maybe the fuse is bsted and also check the wirings.

Feb 08, 2010 | 2000 GMC Jimmy

1 Answer

Ford focus-99 abs module

if the ABS system is functional u will have no ABS warning light showing in the dash except when u first turn the key on, that is a prove out to show the indicator light is working. If the ABS has a problem of any kind the light will always stay on when driving and the system will be disabled..

Jan 22, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2000 GMC Jimmy Logo

557 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

75797 Answers


Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides