Question about 2000 Daewoo Korando

1 Answer

Can i please get some info on how to replace front wheel bearings please

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,230 Answers

Hi there,

Well first of all you can please follow the below steps -
1. Jack up the car. Use jack stands if possible, or blocks if not.
2. Remove tires on the front. Remove brakes.
3. Take out the grease cap (the center).
4. Pull out Cotter Pin. Take nut out.
5. Pull Rotor out. Take grease seal off of the back of the rotor. Pull out inner and outer bearings.
6. Using hammer and punch, knock out racings from the back of the center of the rotor (very important to use new races, don't use the old ones). Clean out the center of the rotor with a clean rag.
7. Using the new bearings, replace the old ones, tapping them into place. It doesn't matter which one you install first.
8. Pack with grease when they are in place. Install new seal after the bearings are packed with grease.
9. Re-install the rotors into car; put brakes back on; replace tires..... You can please follow the below link for more help (the link includes images) - http://autorepair.about.com/od/fixityourself/ss/wh_bearing_old.htm
Please post comments if you need more help or information...........

Good Luck!!

Thanks
 

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I replaced driver side front wheel bearings, but starting to hear squeaks. Is this a lack of packing grease?


Dan, squeaking could be from improperly packed bearing or hub nut not tightened properly. Did you replace the races also.
Check the attached links, They will answer a lot for you.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How to Change Wheel Bearings Step by Step

Pack Wheel Bearings 1994 Ford F150 2WD Pickup Part 5

How To Install Replace Front Brakes 93 97 Ford Ranger 2WD 1AAuto com

Replacing Rotors with Tapered Roller Bearings EricTheCarGuy



Mar 12, 2016 | 1990 Ford Econoline

3 Answers

I have heavy vibraton in front end starting at 30mph up to 65mph. pulld t right


check tyres for failure
check for disc rotor failure ( warped or broken)
check for wheel bearing failure

Mar 06, 2015 | 2004 Chevrolet TrailBlazer

1 Answer

Wheel bearing


Need more info about your problem, make and model, which bearing front or back wheel. The more info you give the better we can help. Please re-post with more about your problem.

Jul 31, 2011 | Chevrolet Monte Carlo Cars & Trucks

2 Answers

I have a 1993 GMC Safari that started making a strange noise from the front end I have taken it to 2 mechanics they both tell me that the problem is the wheel bearing. 1 says the bearing is in a sealed...


I just re-packed the front end bearings. Haynes covers the brakes real well, but not the bearings. Each front wheel has two bearings (one inside the wheel). So you have to remove the wheels, brakes, dust cap, grease seal and brake rotor to access the bearings. .
Expect to replace the grease seal because the rubber will be brittle or hard. Clean and inspect the bearings and races real well. If the bearings are squealing expect to replace some of them also.
Replacing the brakes so the pads stay in place is the trickiest part.

Jan 08, 2011 | 1993 GMC Safari

1 Answer

2002 freelander front wheel bearing replaceing.


The File for this is too Large for FixYa .com Email me @ rejakwilson @ aol.com I Will send Complete File if Procedure

Oct 04, 2009 | 2002 Land Rover Freelander

1 Answer

Can i get step by step instuctions for replacing a wheel bearing


You need to provide more info. Is it a front or rear bearing? That would be a good start.

Jun 21, 2009 | 1996 Ford Taurus

1 Answer

Cant find info or book on repairing the front wheel bearrings on my car,or even a "manual" for a 2001 Hyundai Tiburon!


Yes autozone.com has a repair guide for your car,you will be able to get the steering knuckle off,this is where the bearing is but ir requires a press or an equivlant to remove and replace the bearing.

May 25, 2009 | 2001 Hyundai Tiburon

3 Answers

Wheel hub assembly front 1997 sebring


  1. Raise and safely support the vehicle.
  2. Remove the front tire and wheel.
  3. Remove the steering knuckle assembly, as described previously.
  4. Remove the bolts attaching the hub/bearing assembly to the steering knuckle.
  5. Remove the hub/bearing assembly from the front of the steering knuckle. The bolt-in front wheel bearing used on the vehicle is transferable to a replacement steering knuckle, if the bearing is in serviceable condition. If the bearing will not come out of the steering knuckle, it can be tapped out using a soft-faced hammer.
  6. a567c9e.jpg

  1. Thoroughly clean all parts, including the hub/bearing assembly mounting surfaces on the steering knuckle.
  2. Install the replacement hub/bearing assembly onto the steering knuckle, aligning the bolt holes of the bearing flange to the knuckle.
  3. Install the attaching bolts and tighten evenly to make sure the bearing is square to the face of the steering knuckle. Tighten the attaching bolts to 80 ft. lbs. (110 Nm) on Cirrus, Stratus, Sebring convertible and Breeze, or 65 ft. lbs. (88 Nm) on Sebring coupe and Avenger.
  4. Install the steering knuckle assembly, as previously described.
  5. Install the tire and wheel.
  6. Lower the vehicle and check for proper operation.

Feb 01, 2009 | 1997 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...