Question about 2003 Ford Windstar

1 Answer

Fordwindstar 1996 SEL, all the power on the drivers' side went out, window and sliding door. HELP!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 204 Answers

Check to see if any fuses have blown.

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Mercury Mystique Window


Here are the instructions:
    • Gently remove the door panel of your Contour, ensuring that you don't break the three door clips that hold it on. As you pull the panel from the door, support the panel from below. This will ensure that none of the wiring inside the door is damaged. Release the wiring from the components inside the door, including the power window mechanism, power lock mechanism (if equipped) and the stereo speaker. Place the door panel in a safe area with the clips so they are accessible when you are ready to replace them.
    • 2Remove the window glass by sliding it up and out of the door. Support the glass from the bottom so it doesn't drop and break. Window glass for a Contour can cost around $150 to replace. After you remove the glass, put it in a safe place. You may want to wrap it in old towels or blankets to protect it until you are ready to reinstall it.
    • 3
    • Unplug the wires from your Contour's window motor, and remove the screws from the window motor and regulator. Remove the power window motor and regulator from your Contour to make way for the new parts.
    • 4Install the new window regulator into the door, and replace the screws that held them in place.
    • 5Replace the window glass into the door, and connect it to your Contour's power window motor and regulator assembly.
    • 6Replace the door panel. Reconnect the wiring for the power window and power lock controls, and replace each clip that connects the panel to the door.

Jul 26, 2012 | 1996 Mercury Mystique

1 Answer

My FORD WINDSTAR 2000 SEL driver side sliding door is locked and will not allow me to unlock it even when all other doors have been unlocked.


The door lock actuator is stuck in the lock position you will need to slim jim it open meaning you will have to lose the door lock actuator on the driver sideor replace the door lock lock actuator

Aug 18, 2011 | 2000 Ford Windstar

1 Answer

Wher is the power window relay for 1996 s-10 truck


Your problem is likely in the master switch on the driver side. Try getting a drivers door switch from the junkyard. I have a 96 Silhouette that I experienced the same problem with. After changing out the motor, and the passenger switch I finally traced it to the master switch. Power goes to the drivers door switch first and then over to the passenger door. It could actually be both switches. A bad relay would affect both windows not just the one side.

Jun 05, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

The lock on the power sliding door (driver's side)


You should be able to manually unlock the door and open it,even without the power lock working.The center roller on these vans is prone to wear,causing binding and misalignment of the electrical connectors that you see when the door is open.This may cause the locks to be disabled and the door to not open with the power button.There are three rollers on each door,but many times only the center one is worn out.The installation & alignment of the rollers is critical on this vehicle,so you should consider the dealer for this repair. good luck

Apr 09, 2010 | 1996 Honda Odyssey

1 Answer

Power windows falling down-1996 nissan 200sx se


The problem is with the window regulator, which the motor attaches to. The regulator has come off the window.

Feb 15, 2010 | 1996 Nissan 200SX

1 Answer

Need Manual Driver side Window not working. Fuse diagram would help.


if just drivers side check switch on door pops out and test for power if power to switches will have to remove door panel to check window motor for binding or burnt out

Nov 01, 2009 | 1996 Chevrolet G20

1 Answer

My 1996 landrover discovery only the drivers side window works the sunroofs work but my other 3 door windows dont work at all any help would be usefull


check and see if the window lock is on or not, driver side window and sunroof will still function when window lock is activated however, the other windows will not work, even by the drivers control, it should be the button on the top right next to your power door lock switch,

Sep 16, 2009 | 1996 Land Rover Range Rover

2 Answers

All of the power windows just went out on my 04 Jeep Grand Cherokee. The power locks work on the passenger side door but not on the drivers side. None of the controls work on the drivers side including the...


slide the rubber boot up and check the wires in the hinge of the doors. I will bet anything that the wires are broken. that was what was wrong with mine. just splice them back together and everything should work fine.

Mar 09, 2009 | 2004 Jeep Grand Cherokee

4 Answers

1996 honda civic lx passanger power window problem


I had this problem as well as 33 others I've spoken to online. The main floor harness runs thru the drivers side front fender and plugs into the drivers door. The harness in 1996 civics are an inch or 2 too short so after a few years a few of the 25 thru 27 wires in the plug #C556 either break off or pull out of the plug. Since the drivers door contains the master power window and lock switches and the power mirrors can also be affected it can seem like everyones problems are in different parts of the car but they are all part of the same default. So I went to ebay and purchased a floor harness with full power options and installed it myself. Until my part came in I just went to a junk yard and cut off a good plug then spliced it into my existing floor harness. Hope this helps. It took me 4 months to figure this problem out!!!

Aug 01, 2008 | 1996 Honda Civic

Not finding what you are looking for?
2003 Ford Windstar Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...