Question about 1999 Ford Super Duty F 550

2 Answers

How to repair clutch pedal safety start switch on Ford Truck F550, 1999

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 324 Answers

I believe the switch is under the dash near the top of the pedal arm, just take it off and put a new one in it's place.

Posted on Feb 06, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

Clutch Pedal Position (CPP) Switch
The clutch pedal position switch (CPP) is controlled by the clutch pedal. Depressing the clutch pedal manually closes the CPP switch and allows engine cranking. The CPP switch will also deactivate the speed control system.
--------------------------------------------------------------------
303-14A: Electronic Engine Controls — Gasoline Engines 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Clutch Pedal Position (CPP) Switch Removal

  1. how to repair clutch pedal safety start switch on - sxo~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always disconnect the battery ground cable prior to working on the electronic engine controls.
    Disconnect the battery ground cable; refer to Section 414-01 .
  1. Disconnect electrical connector from clutch pedal position switch (CPP) (9A837).
  1. Release the clutch pedal position switch (CPP) (11A152) from the orientation clip.
  1. Remove the plastic retainer.
    1. Push the lock tabs together.
    1. Slide the plastic retainer off the clutch pedal position switch.
  1. Remove the clutch pedal position switch.
Installation
  1. Follow the removal procedure in reverse order.

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the break safety switch located in a 2009 Ford Fusion


Jeanette, break switch is above brake pedal arm, safety neutral switch is on transmission, clutch pedal safety switch above clutch pedal arm. Links below have pics.
to show your appreciation press the helpful button and follow me on fixya for more tips and info.

06 ford fusion brake light switch replace

How To Test and Replace the Neutral Safety Swtich Inhibitor Switch P0705

Clutch switch behind clutch pedal Ford Focus Forum Ford Focus ST Forum...

Replace master cylinder clutch Ford Focus Forum Ford Focus ST Forum Ford...

Feb 15, 2016 | 2009 Ford Fusion

1 Answer

Trouble shoot 2500masda truck that won t start after I replace clutch and slave cylinder


Did you reconnect the wires and re-position the clutch safety switch at the clutch pedal assembly? If this switch is not positioned or connected correctly it will not allow the truck to start.

Feb 25, 2015 | 1999 Mazda Pickup

1 Answer

Starter on truck is not starting truck


There are safety switches on the brake pedal lever(automatic) or clutch pedal lever(stick) depending on year. What usually happens is that your feet bump or break the switch and you lose the starter pulse. This switch is suppose to prevent "runaway" vehicles by insuring that your foot is on the brake pedal or clutch when you use the starter. Look under the drivers dash on the brake or clutch lever.

There can also be another switch on some models that is for safety and insures the gearshift is in Park. Finally, some ignition switches have adjustments where they attach to the steering column. The ignition switch has slots which allow the adjustment.

The loss of your signal to the starter relay can be verified by using a Voltmeter on the small wire of the starter relay, then backtrace the above switches to restore the signal.

Diagrams are on the Web by doing a search specific for the year, make, and model followed by which part you want to find. (example -fusepanel or powerbox)

Oct 20, 2014 | 2011 Ford F-150 Regular

1 Answer

Wireing diagram for 1972 ford f250 starter safty switch & backup ;light switch


neutral safety switch is bad or miss aligned this switch is located at the bottom of the steering column unless it's a standard then it was connected to the clutch pedal or stick shift depending on tranny option being it is a truck the most common spot was at the bottom of the column

Sep 01, 2014 | Cars & Trucks

2 Answers

Neutral safety switch


DOES IT START WHEN YOU PUT IT IN NEUTRAL, ALSO THE NEUTRAL SAFETY SWITCH IS LOCATED UNDER THE DRIVERSIDE CLUTCH PEDAL UP IN THE COLUM, IT SHOULD HAVE ONLY TWO WIRES FOR A REPLACEMENT.

Aug 23, 2014 | 2004 Ford Ranger

2 Answers

I am having to slam my cltch pedal to the floor to get it to start


lay on the drivers side floor board and you will see there is a switch on the brake peddle... That is the brake light switch..
Now look next to it on the clutch peddel... that is the possative clutch diseguagement switch... You will want to adjust that so it is closer to the peddel...
Easy FixYa!

Sep 30, 2010 | 1993 Ford F250

2 Answers

Having trouble with my 1989 ford f-150 starting, it is a standard tranny, just changed the clutch and slave cylinder the truck started before I did this. The lights work and all the power options, but it...


There is a safety switch off of the clutch pedal so you don't start it with it in gear, and the clutch out. This is adjustable,and sounds like is your problem. Look under your dash for a small switch that is acuated by the pedal.

Aug 21, 2009 | 1989 Ford F 150

1 Answer

Isuzu Trooper Clutch Pedal Issue


either it is a clutch fluid line busted (most likely)or its you clutch master you can start it anyway give a little gas in 1st and start it shut it off b4 starting i drove my volvo 740 home like that once nerve wrecking but save towing money

Jun 19, 2009 | 1993 Isuzu Trooper

2 Answers

Neutral safety switch....I think


The switch is located at the top of the clutch pedal assembly, above your feet. Its a little cramped, but its a simple dc two wire switch, you should be able to check it with a meter for power and to see if the switch does indeed need replacement. If thats the problem, when you see the new switch, you'll know it goes in, very easy. good luck

Aug 12, 2008 | 1988 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

2,026 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...