Question about 2001 Chevrolet Suburban

3 Answers

The Mirror adjustment button on the drivers arm console got damp. The mirrors (both sides) will not adjust up or down. The other directions are slow. Probably corrosion. How do I access this switch to clean the contacts?

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

You should check the fuse in the fuse panel it usually goes out first when the switch gets wet. By removing the console look for screws to undo them. if there is any. It's really easy to do.

Posted on Feb 06, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers

The panel that houses the power window and lock switch and mirrors all come off the door skin. if you pull up on the exterior edge the panel will unsnap and remove. disconnect wiring and you will have accedd to the switch

Posted on Feb 06, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

You will have to pull the door panel off, be sure to remove any hidden screws, most of the panel is held on by clips.
I would recommend a new switch if the old one is coroded.

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Memory seats adjust on there own as well as mirrors


BCM has nothing to do with this function , MMM - memory mirror module !
Memory Mirror System Operation
The MMM is capable of storing mirror position for 2 different drivers. Mirror position is determined by both horizontal and vertical position sensors in each of the power mirrors. The MMM supplies a reference voltage and a low reference to these sensors and determines mirror position through the horizontal and vertical position signal circuits.
The MMM receives power through the battery supply voltage circuit and the MIR/LOCK fuse and a constant ground source. Any time that battery voltage is disconnected and then connected from the MMM, the MMM will enter the mirror relearn mode. The mirror relearn mode can also be commanded using a scan tool. Refer to Memory Mirror Module Learn for further information.The memory switch receives power through the battery supply voltage circuit and the MIR/LOCK fuse. The MMM upon receipt of a memory switch signal input, a class 2 message from the SIC or a class 2 message from the PCM indicating that the transmission is in park, will then supply battery voltage and ground to the appropriate power mirror motors through the mirror motor control circuits to move the mirrors to the predetermined positions.

DTC B1586, B1596, B1616, or B1626
The mirror horizontal and vertical position sensors are potentiometers. The Memory Mirror Module (MMM) provides these sensors with a 5 volt reference circuit and a low reference circuit. The MMM monitors the horizontal and vertical position sensor signal circuits which change values based on mirror position. These voltage values are used to determine mirror position and can be set into memory. When the MMM receives a memory recall request, the MMM will control the power mirror to the memory position based on the horizontal and vertical position sensor signal values.

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, observe the mirror horizontal and vertical position parameters in the Memory Mirror Module (MMM) data list.
Operate both the left and right mirrors through the full range of movements.
Does the scan tool indicate that the left and right mirror horizontal and vertical position parameters are within the specified range?

Memory Seat System Components
The memory seat system consists of the following components:
• Power seat switch assembly
• Memory recall switch assembly
• Horizontal adjuster motor
• Front vertical adjuster motor
• Rear vertical adjuster motor
• Recline adjuster motor
• Memory seat module
• Memory mirror module
• SEAT 25A circuit breaker
• MIR/LOCK 3A fuse

Your best bet , take it to a qualified repair shop !

May 23, 2017 | 2002 Cadillac Escalade

1 Answer

How to replace 04 ranger mirror switch


Does the other side mirror work?

If the other side mirror adjusts with the switch, then it could be an issue with the mirror which isn't working.
Usually a mirror has two motors, one for up/down and another for left/right. If the mirror works in one direction and not in the other, yet the mirror on the other side works in all directions, then the issue is not the switch, but the mirror.

Unless none of that is relevant and you are talking about the fold function.

If neither mirror folds when you depress the fold button, then you need to check or change the switch as the most likely cause of the issue.
If you can provide me with a picture of the switch, then I can try to advise on how to remove and replace it.

Nov 13, 2012 | 2004 Ford Ranger

1 Answer

Driver's side rear view mirror - how to fix adjustment mechanism?


I would first take the mirror apart to make sure the cable is still attached. Then if it is I would soak the cable with penetrating oil and put it back together and hope for the best.

Jul 30, 2012 | Cars & Trucks

1 Answer

The drivers side mirror adjusts up and down but not side to side. Car has electric mirror adjust.


You will probably need that side mirror as the motor has failed. The motor in the mirror will control both directions, but sometimes loses the ability to control either up/down or in/out. Check the other side if it also doesn't adjust side to side I'd then suspect the mirror switch.

Jan 31, 2011 | Toyota Camry Cars & Trucks

1 Answer

1994 chevy silverado driver side mirror is loose


try removing the black cover that wraps out from the door to the mirror just be carefull.....plastic ****.

Apr 25, 2010 | Chevrolet Silverado Cars & Trucks

1 Answer

Control Review Mirror. Being able to adjust it


Where is your side mirror adjustment knob? If you turn the directional straight up to 12:00...That adjust your rearview mirror.

Sep 08, 2008 | 2002 Mercedes-Benz S-Class

1 Answer

Side view mirrors


the 4 buttons around that switch are the ones you press to move the mirror. to adj the drivers mirror, move the switch to the left, to adj the passenger mirror, move it to the right.

then you press one of the 4 buttons

Jul 21, 2008 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
2001 Chevrolet Suburban Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...