Question about 2003 Chrysler Town & Country

2 Answers

Ran up on a curb busted a tire now the transmission is going in and out meaning it will go but fills like it is in neutral

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

You need to check and see if you damage the linkage or the sensor on the transmision give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your van wish you the best of luck Michigan Man.

Posted on Feb 06, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

You might need a transmission rebuild or a new one.
Sorry!

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rides bumpy about 30 mph


Possible you damaged a wheel bearing, bushing, bent wheel studs, etc. Have a reputable repair shop go over it very carefully.

Jul 17, 2016 | Cars & Trucks

1 Answer

What is the ignition timing for 2002 nissan hardbody 2000i 16v


Here are the 3 engines listed for this year. IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 2.4L SFI 4cyl

The Ignition Timing

18-22 DegreesBefore top dead center - When throttle positionsensor disconnected and using suitably programmedscan tool.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (750-850 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (700-800 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI SC 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chockdrive wheels, curb idle speed (700-800 RPM)transmission in neutral.

Jun 05, 2015 | Nissan Hardbody Cars & Trucks

3 Answers

I took out the transmission plug and started my 1998 Pontiac Sunfire to check transmission oil and it poured out until there was no more coming out. Does this mean the transmission is now empty of its oil...


The vehicle needs to be level. If you have the front jacked up and not the rear the level will be off.

The vehicle also need to be running before you pull the plug.

Once the vehicle is level, running, and up to temp pull the plug. Remove the fill cap and add fluid until it starts to come out of the hole. Reinstall the plug. Your good to go!

Sep 25, 2010 | Pontiac Sunfire Cars & Trucks

1 Answer

What are timing marks on 2001 kia rio 1.5 engine


3-13 Degrees
Application:
With manual transmission

Note :
Before top dead center, at specified curb idle speed.
Locate data link connector & connect jumper wire
between ground & engine test terminals.
After completing adjustment, remove jumper wire.
Curb idle speed (750 RPM) transmission in drive.

3-13 Degrees
Application:
With automatic transmission

Note :
Before top dead center, at specified curb idle speed.
Locate data link connector & connector jumper
wire between ground & engine test terminals.
After completing adjustment, remove jumper wire.
When adjusting idle speed, set parking
brake & chock drive wheels.
Curb idle speed (750 RPM) transmission in neutral

Aug 18, 2010 | Kia Rio Cars & Trucks

1 Answer

Steering wheel is vibrating and shaking


it would be one of two things.....most commonly, there is a busted belt in one of the tires. Hitting a chuck hole pretty hard will cause this, or a curb.....the other would be that one of the balance weights is gone, causing the tire to be out of balance.....

Apr 16, 2009 | Ford Taurus Cars & Trucks

2 Answers

90 camry goes backward and not forward


maybe its the bearings did you check them......?

Dec 23, 2008 | 1991 Toyota Camry

Not finding what you are looking for?
2003 Chrysler Town & Country Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...