Question about 2005 Chevrolet Impala

1 Answer

Cannot open doors with remote key - 2005 Chevrolet Impala

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

Check battery in the remote this is usually the first problem.
You can buy the battery at Best Buy or any place that sales watch sized battery's but first remove the bottom of the remote and read what size battery you need it show what it is on the battery.
These battery's are around $5-8 bucks.

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My MB ML350 stick key (metal key) wont unlock the door. The key goes in, it turns but the lock will not open.


Check the door lock fuse in the fuse panel... try the key on another door... may just be that the manual lk is malfunctioning on that door... if the other doors don't respond and the fuse is good then the key probably needs to be reprogrammed by the dealer to the door... happens when your battery dies or is replaced.

Dec 02, 2014 | 2008 Mercedes-Benz ML 350

1 Answer

My highlander 2008, the doors can be locked and open with key and remote but cannot open the trunk with key and remote


To make the rear door open, you have to hold the button for a while. If the battery is weak, that will drain the power and the door will not open. Try the other remote and see if it works. At that point, I would replace the batteries in both remotes anyway.
That would be the fastest and cheapest way to eliminate one possible problem.
If the inside open button works to open the door, I would say the mechanism is working fine and it is the batteries.
I had to replace the batteries in both my remotes at the 3 year mark. That should be about now, the second time, for yours.
Dave

Sep 01, 2014 | 2008 Toyota Highlander

1 Answer

How do you program a replacement key for a lexus es 330 2004


Here are the instructions from the factory manual. They must be followed exactly.
2004 ES330
1. Driver's door open, all other doors closed, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.

2. Within 40 seconds:
Close and open driver's door twice.
Insert and remove the key from the ignition switch.

3. Within 40 seconds:
Close and open driver's door twice.
Insert the key into the ignition switch and close the driver's door.

4. Switch ignition ON and OFF:
A. Once to program a key remote transmitter code whilst retaining the original codes.
B. Twice to program a key remote transmitter code whilst erasing the original codes.
C. Three times to check how many key remote transmitters are currently registered.
D. Five times to erase all registered codes.

5. Remove key from ignition switch. System should now lock and unlock vehicle
once, twice or five times depending which mode has been selected. One to four
times, slowly, to indicate number of key remote transmitters registered.

6. Within 40 seconds:
Press and hold LOCK and UNLOCK buttons simultaneously for 1.5 seconds.
Within 3 seconds: Press any key remote transmitter button.

System should now lock and unlock vehicle once to confirm registration or twice
to indicate registration has failed.

7. Within 40 seconds:
To program additional remotes repeat step 60 now on each additional
remote you want programmed.

8. To exit programming mode open driver's door or insert key into ignition.
9. Step out of car with remote(s) in hand and test remote(s).

Nov 01, 2011 | 2004 Lexus ES 330

1 Answer

Neither key fob is working to open the car with


open door. when alarm goes off put key in ignition and turn it on start car. this should disarm the factory alarm.

Feb 08, 2010 | 2005 Chrysler Crossfire

1 Answer

1997 camry remot key


Try this.

key not in ignition.
driver door open-others closed
driver door unlocked

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice
this is rewrite mode,have all remotes to reprogram
it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possesion,you are done.

to end mode open door or insert key into ig.you can do up to 4 remotes.read this a couple of times to get the sequence down.there are time restraints,but if you go in order it will work.do not wait more than a second b/t each step and you will be ok.i know from experience that you can do this as fast as you can and it will enter mode.if steps out of order or you wait to long it wont.print this and have in lap,read ahead of what you are doing.good luck.

Jun 10, 2009 | 2001 Toyota Camry

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

1 Answer

Drivers power lock will not unlock with remote.


the door lock actuator is defective, they get really hard to move when they go bad, that is why the difficulty with the key.

Mar 31, 2009 | 2000 Ford Explorer

1 Answer

Need programming instructions for RKE for 2000 Mazda 626


2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Sep 03, 2008 | 2000 Mazda 626

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2005 Chevrolet Impala Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...