Question about 1989 Jeep Wrangler
It shows a high and low on the lever but it acts as if there is only one speed
I took off the air filter and looked around for anything abnormal. Saw a black connecter all by itself. look around for a bit and saw the other haf laying on the exhaust manifold. Cleared the melted plastic and plugged it in. Instant and dramatic change. Bg
Posted on Feb 07, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Feb 20, 2017 | Pontiac Cars & Trucks
Feb 11, 2017 | GMC Cars & Trucks
Dec 10, 2016 | 2006 Hummer H3
Dec 04, 2016 | Cars & Trucks
Nov 25, 2016 | 2003 Pontiac Montana
Feb 09, 2016 | Cars & Trucks
Body control module (BCM)
Wiper PCB relay
Wiper high PCB relay
Windshield wiper motor
Windshield washer fluid pump
Windshield washer fluid level switch
WPR fuse 25 A
WSW fuse 10 A
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....
Dec 20, 2015 | 2008 Chevrolet Impala
Body control module (BCM)
Wiper 1 relay
Wiper 2 relay
Windshield wiper motor
Windshield washer pump
Windshield washer nozzles
Windshield washer solvent container
Windshield wiper arm and blade assemblies
Windshield wiper transmission
WIPER/SW 10A fuse
WIPER 25A fuse
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
Dec 05, 2015 | Cars & Trucks
Sep 15, 2014 | 2008 Jeep Patriot Sport
May 27, 2009 | 1994 Ford Mustang
130 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: