Question about 2001 Dodge Ram 2500 Truck

1 Answer

No turn signals,hazards,brake lites,already replaced turn signal switch,brake switch,ignition this is a 2000 ram 2500 4x4 cummins

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 128 Answers

After you checked all fuses and ensured they are good, and checked all bulbs and sockets for burning or corrosion. Confirm power and grounds to all wiring to the lights in the back with a dvom (digital volt ohm meter), check especially the common ground for all these lights, should be in left side fender but trace it manually and see that the connection is good and solid on the chassis and that no rust or corrosion are built up there. also you could try running a jumper ground wire to the ground side of the wiring to the bulbs to check that this is or is not the problem. but be sure to only put the good jumper ground you create to the ground side or you will create a dead short and burn fuses or possible cause damage or even fire. if you are unsure about checking these things you should bring it to a certified mechanic who specializes in checking wiring and electrical problems. hope this will help you. good luck.

Posted on Feb 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

No turn signals possible bad ground


If you only have 7 volts at that fuse your problem is in the power side of the circuit ! You need a power distribution diagram to find where that fuse gets it's power from , you have unwanted resistance in that circuit . It's not a ground problem , you need to do voltage drop testing on that circuit ! Do your brake lights work ? The power for the turn signal , ABS , Stop , an SRS fuse's in the left side instrument panel fuse block come fro the ignition switch ! Your ignition switch may be the problem ! SRS is air bag system !

Aug 05, 2015 | 2000 Chevrolet Monte Carlo

2 Answers

Replace my brake switch on my 2000 Dodge ram pick up and my brake lights still don't work


Brake switch must be adjusted such that it is depressed with pedal up and released as soon as pedal is slightly depressed.

Feb 26, 2015 | Dodge Cars & Trucks

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

2 Answers

After using turn signal you can still hear clinking, is hazard relay part of turn signal


The hazard switch is also the device that supplies the turn signal "flash". If you continue to hear the noise of the turn signal flashing when the turn signals off than the problem is the turn signal switch. It is grounding The purple wire from the hazard switch which makes the hazard switch think the turn signal is on. The fix for this is to relace the turn signal/multi-function switch. Typically they will start to go bad in stages. Your symptom is the first stage. Eventually either the turn signals or the brake lights will also sto working. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 10, 2012 | 2000 Oldsmobile Alero

1 Answer

1992 Ford Ranger Turn signal/Hazard light issue


Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Apr 19, 2010 | 1992 Ford Ranger

1 Answer

2000 Chevy CK, have hazard lights, turn signals,


test your brake switch located on the brake fulcrum. you can unhook the wires and usea paper clip to connect the two wires together if the brake lights come on then replace the switch, if it does not come on and the bulbs are ok then replace turnsignal switch.

Jul 18, 2009 | 1999 Chevrolet 3500

1 Answer

No turn signals, hazards or brake lights


replace the turn signal switch in the steering column

May 14, 2009 | Ford E-350 Cars & Trucks

1 Answer

Signal lights stay on


Its common for the sockets to burn up.  If you installed and the lights are still coming on.  The issue is the hazard light switch is bad.  If it were me I would replace the burnt socket anyway since it has been damaged and replace the hazard lite switch too.

Mar 19, 2009 | 2000 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...