Question about 1990 Nissan Hardbody King Cab

1 Answer

Putting the 2.4 liter in time

Putting the 2.4 liter motor in time

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Nissan Master
  • 2,030 Answers

If you want to know the time to install the motor, it is 13 1/2 hours to do the job properly

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set crankshaft timing on 1992 honda prelude 2.3 liter?


here is a u-tube video with a good tip for making sure the timing marks dont get move once set may help
How to replace timing belt on Honda Prelude 92 96 2 3 lt H23a1

Jul 28, 2014 | 1992 Honda Prelude

1 Answer

Are a 1993 4.0 liter high output 2 wheel drive Jeep Grand Cherokee countries have the same block as a 1990 Jeep Grand Cherokee Laredo 4 wheel drive it also has the 4.0 liter engine but it is not the high...


the first grand cherokee laredo was in 1992 . it was all jeep sports back then, the blocks are all the same .you will need to use some of the sensors from the old motor, the distributor and oil sending unit and temp sensor. will be no problem. if I can put a ford ranger motor in a mercury sable your swap is easier

Dec 05, 2012 | Cars & Trucks

1 Answer

How do i check fluid for convertable top


"How do I get the air out of my hydraulic system"?
  • Remove the reservoir plug on the motor pump. Leave the plug out and do not put back until you have finished.
  • Fill the reservoir 3/4 full with fluid (to the bottom of filler plug hole). Put a rag under the hole to catch overflow that will occur as system fills.
  • Run the pump for 15-20 seconds. Stop. Check your fluid level and refill to bottom of filler hole. Continue running the motor in the same direction for an additional 15-20 seconds. When the top gets to the end of cycle, check your fluid level, fill to bottom of filler hole, and run the motor in the opposite direction.
  • You are literally running the top all the way up and down sereral times. Checking the fluid level as you go and fill as required, leaving reservoir 25% empty.
  • When you are no longer able to add fluid, put the top in the down position. Check the fluid level one last time, should be to bottom of filler hole. Put the plug into reservoir.
    "How do I get the air out of my hydraulic system"?
  • Remove the reservoir plug on the motor pump. Leave the plug out and do not put back until you have finished.
  • Fill the reservoir 3/4 full with fluid (to the bottom of filler plug hole). Put a rag under the hole to catch overflow that will occur as system fills.
  • Run the pump for 15-20 seconds. Stop. Check your fluid level and refill to bottom of filler hole. Continue running the motor in the same direction for an additional 15-20 seconds. When the top gets to the end of cycle, check your fluid level, fill to bottom of filler hole, and run the motor in the opposite direction.
  • You are literally running the top all the way up and down sereral times. Checking the fluid level as you go and fill as required, leaving reservoir 25% empty.
  • When you are no longer able to add fluid, put the top in the down position. Check the fluid level one last time, should be to bottom of filler hole. Put the plug into reservoir.
  • Apr 01, 2012 | 2004 Ford Mustang

    2 Answers

    How can I get visual information of where the timing marks are on a 4.4 liter motor. This is a 1999 BMW 7 series E38


    hi unfortunately there is no external marks to go by this is only achieved by removing the rocker covers and then putting it into top dead centre and seeing if the 2 camshaft marks align up at the top..

    Dec 31, 2010 | 1999 BMW 7 Series

    1 Answer

    Looking to do a motor swap in a 98 sunfire...what motors fit?


    It is true, you can only put another 98 2.2 liter in it. They did come with a 2.4 liter but you have to swap the motor, transmission, wiring harness, computer, and God knows what else. I would go with the 2.2 liter and check into some performance aftermarket parts for the 2.2, computer chip, performance exhaust and so on, somewhere like Summit Racing.

    May 23, 2010 | 1997 Pontiac Sunfire

    1 Answer

    Where and how many timing belts


    Ford explorer 4.0 liter motors have 2 timing chains. If they don't rattle, leave them alone.

    Jul 23, 2008 | 2002 Ford Explorer Sport

    Not finding what you are looking for?
    1990 Nissan Hardbody King Cab Logo

    Related Topics:

    67 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...